Ultrasound-assisted extraction (UAE) and microwave-assisted extraction (MAE) of bioactive compounds, peels from Opuntia engelmannii cultivar (cv.) Valencia were optimized by response surface methodology. Randomized extraction runs were performed for each of the technologies employed in order to build effective models with maximum (bioactive molecules content and yield) and minimum (antioxidant activity) responses. A 5-level, 4-factor central composite design was used to obtain target responses as a function of extraction time (t), solid to liquid ratio (S/L), methanol concentration (metOH), and temperature (T). Specific response optimization for each technology was analyzed, discussed, and general optimization from all the responses together was also gather. The optimum values for each factor were: t = 2.5 and 1.4 min, S/L = 5 and 5 g/L, metOH = 34.6 and 0% of methanol and T = 30 and 36.6 °C, achieving maximum responses of 201.6 and 132.9 mg of betalains/g, 13.9 and 8.0 mg of phenolic acids/g, 2.4 and 1.5 mg of flavonoids/g, 71.8% and 79.1% of extractable solid and IC₅₀ values for the antioxidant activity of 2.9 and 3.6, for UAE and MAE, respectively. The present study suggested UAE as the best extraction system, in order to maximize recovery of bioactive compounds with a high antioxidant activity.

Consumer interest in the use of natural ingredients is creating a growing trend in the food industry, leading to research into the development of natural products such as colorants, antimicrobials and antioxidant compounds. This work involves an extensive morphological (using physico-chemical assays), chemical (antioxidant activity assays) and microbiological (Gram-positive and negative strains) characterization of prickly peras (Opuntia ficus-indica (OFI) var. sanguigna, gialla and Opuntia engelmannii) fruits. Through chromatographic assays, these species have shown interesting contents of hydrophilic (sugars, organic acids and betalains) and lipophilic (tocopherols and fatty acids) compounds. While Opuntia engelmannii exhibited higher content of betacyanins and mucilage, OFI varieties sanguigna and gialla displayed greater organic acid content. The sanguigna variety also showed the highest α-tocopherol content. All this compounds could be the responsible of enhancing the bioactivity of this variety, which can be observed in its antimicrobial potential, tested in the studied strains too. Results revealed that Opuntia spp. could be used as a nutraceutical and/or food additive, maintaining and promoting health and life quality.

Artichoke wastes after processing represent 60–70% of the raw material and are a potential source of inulin and polyphenols, bioactive compounds that can be valorized as food ingredients or nutraceutical products. The aim of this work was to assess and optimize the extraction of these compounds from artichoke wastes using water or water–ethanol mixtures as extracting agents. For simultaneous inulin and polyphenol extraction and to achieve high antioxidant activity in extracts, the best process conditions using water as an extracting agent were T = 89 °C and t = 139 min, where 80% of the inulin content, 60% of the total phenolic content (TPC) and 56% of the antioxidant activity (Aox) were obtained. For water–ethanol extractions, the best results were obtained with EtOH = 22.4%, T = 81 °C and t = 217 min, leading to extraction yields of 90% of TPC, 38% of Aox and 58% of inulin content. From these results, we recommend the use of water for the recovery of inulin and polyphenols from artichoke wastes. Although the extraction yield of polyphenols is lower in water treatments, the amount extracted is considerable and it is a greener option when compared with water–ethanol mixtures.

Food wastes have traditionally been considered as dead-end materials; however, recent international, national, and regional policies strongly promote the use of these wastes as potential resources. This change of perception considers the need for sustainable exploitation of natural resources. In this context, artichoke processing produces high amounts of wastewaters, and specifically, wastewaters from the artichoke blanching step present a high content of valuable biocomponents such as carbohydrates and phenolic compounds (e.g., chlorogenic acid, 1700 ppm). In this work, the recovery of chlorogenic acid by applying sorption processes was studied. Five resins were tested, and it was found that the resin XAD 7 HP presented the best total adsorption-desorption yield (72.8%) at 20 °C. It was also found that there was a strong variation of the adsorption ratio depending on solution pH (3–7). Four models of isotherms were applied to the adsorption processes, and the Langmuir isotherm better explained the adsorption behavior. The kinetic study showed that the adsorption and desorption of chlorogenic acid followed a pseudo-second order model where the kinetic constant depended on the adsorbate concentration. In addition, it was found that the sorption process was controlled by more than just the intraparticle diffusion mechanism.