Wenying Jiang

Wenying Jiang


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 December 2019 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
YXYanwu Xu
Yanwu Xu
ZZZhuoran Zhang
Zhuoran Zhang
YJYunyi Jiang
Yunyi Jiang
JHJian Huang
Jian Huang
WJWenying Jiang
Wenying Jiang
Due to its high power density, the fractional slot concentrated winding (FSCW) permanent magnet synchronous machine (PMSM) is a competitive candidate for the aircraft starter generator (SG) system. However, the short circuit (SC) fault, especially the turn-to-turn SC fault, is the obstruct crux in aviation applications. The turn-to-turn SC current can be restricted to a permissible level with higher reactance and the current injection mitigation method. However, higher self-inductance always leads to lower power density. So far, there have been no numerical criteria for the trade-off between the two characteristics in machine design. In this paper, an analytical model based on flux distribution is used to estimate the SC current. The effectiveness of the d-axis current injection mitigation method is numerically analyzed in the series and parallel connected windings individually. The requirement for PMSMs to survive the turn-to-turn SC fault is derived. The mathematic analysis is verified by finite element analysis (FEA) and experiments on a 12-slot, 10-pole PMSM. The paper provides theoretical support for designing high-performance PMSG with SC current mitigation ability for the aviation power system.

9 July 2018 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
WJWenying Jiang
Wenying Jiang
SFShuo Feng
Shuo Feng
ZZZhuoran Zhang
Zhuoran Zhang
JZJiamin Zhang
Jiamin Zhang
ZZZhen Zhang
Zhen Zhang
This paper presents an effective method for calculating the current excitations for optimal operating condition of interior permanent magnet (IPM) synchronous machines for traction application. The relationships between torque, current amplitude, and current angle during optimal operation are studied. For a given torque and speed command, the steps of searching for the ideal current excitations can be simplified using a script developed in ANSYS Maxwell, which significantly accelerates the process of evaluating performance and creating efficiency map of an IPM machine.

22 December 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
CAClint Yoannes Angundjaja
Clint Yoannes Angundjaja
YWYu Wang
Yu Wang
WJWenying Jiang
Wenying Jiang
In recent years, the electric vehicles (EVs) power management strategy has been developed in order to reduce battery discharging power and fluctuation when an EV requires high and rapid discharging power due to frequent stop-and-go driving operations. A combination of lithium-ion battery and supercapacitor (SC) as the EV’s energy sources, known as a hybrid energy storage system (HESS), is a promising solution for fast discharging conditions. Effective power management to extensively utilize HESS can be developed if future power demand is accessible. A vehicular network as a typical form of the currently developed internet of things (IoT) has made future information obtainable by collecting information on surrounding data. This paper proposes a power management strategy for the HESS with the support of IoT. Since the obtained information from the vehicular network could not directly be used to improve HESS, a two-level control structure has been developed to perform future data prediction and power distribution. A fuzzy logic controller (FLC) is utilized in level one control structure to manage a HESS power split based on future information. Since FLC requires future information as a reference input, the future information is obtained by using an artificial neural network (ANN) in level two control structure. The ANN provides a direct prediction that could approximate the future power demand prediction with the assumption that the vehicular network scenario is deployed to obtain surrounding information. Simulation results demonstrate that the average discharging battery power and power variation are reduced by 46.1% and 52.3%, respectively, compared to the battery-only case.

11 March 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
JHJian Huang
Jian Huang
ZZZhuoran Zhang
Zhuoran Zhang
JHJianbin Han
Jianbin Han
WJWenying Jiang
Wenying Jiang
This paper proposes a two degrees of freedom (TDOF) control with torque current compensating method (TCCM) to enhance the dynamic performance of permanent magnet generator (PMG) system when load changes. Firstly, the mathematic model of PMG system with active front-end rectifier is introduced. Based on the system model, the proportional-integral (PI) controller of current loop is designed, and the TDOF controller designed with internal model control (IMC) principle is derived for voltage loop control. There are two sets of parameters in the TDOF controller, one is used to regulate the system tracking performance when the command DC-link voltage changes, and the other is used to regulate the system anti-disturbance capability when the electrical load changes. Secondly, the TCCM is proposed to further improve the system dynamic performance. The variation of torque current is applied to revise the command DC-link voltage, namely, the command DC-link voltage increases under loading occasion and decreases when unload occurs. The TCCM needs no additional hardware and is simple to implement. Simulation and experimental results verify the effectiveness of the proposed method.

27 December 2019 in Energies
Verified
Journal Article
Open access
PDF file
WJWenying Jiang
Wenying Jiang
QGQiqi Guo
Qiqi Guo
ZZZhen Zhang
Zhen Zhang
In order to accurately evaluate the performance of a traction machine/drive system, it is necessary to have an accurate excitation source which considers current harmonics. In this paper, four machine/drive systems with different excitation sources have been modeled, simulated, and studied to evaluate the effects on permanent magnet synchronous machines (PMSMs) from different perspectives. In Model I, the excitation is an ideal sinusoidal current source with no harmonics. Model II is excited by an ideal sinusoidal voltage source regardless of the pulse width modification’s (PWM’s) influence. Model III takes into account the influence of current harmonics under space vector pulse width modulation (SVPWM) control. Model IV is based on the equivalent circuit extraction (ECE) model (a look-up table motor model). We simulate these four models and study the characteristics of the excitation sources, based on the observations of current harmonics, torque, electromagnetic force, computation time, and efficiency. Experiments are also conducted to show that Model III allows the most precise study of the considered system. Model IV is a good substitution, providing similar results with a shorter running time.