Purpose: Centrifugal pumps are prone to vibration problems during operation due to poor dynamic characteristics of its impellers that serve as the only running parts of such devices; the dynamic characteristics of the impeller during operation are the main reasons for the vibration of the centrifugal pump. Therefore, it is important to study the internal fluid flow and its influence on the dynamic characteristics of the pump impeller and to explore the causes of vibration during the transient start-up process. The understanding of such phenomena may lead to better design of such impellers. Methods: The geometry of the flow channel inside the centrifugal pump is established using Creo 4.0 software (American PTC company). The internal fluid flow computer simulation is carried out using Flomaster V9 software (UK Flowmaster company) to obtain the variation law of speed and flow during the start-up of the centrifugal pump, which is loaded into the simulation calculation of the centrifugal pump. The variation of speed and flow during the start-up process was further processed using the fluid-structure coupling method, and the structural vibration characteristics of the impeller under transient radial force are obtained by harmonic response analysis. Results: During the starting process of the centrifugal pump, the speed and flow first increased sharply and then decreased until reaching a stable process. During this period, the impeller vibration changed sharply; the overall vibration amplitude increased and fluctuated stably at the amplitude of 0.01 mm. In the unsteady numerical simulation of the centrifugal pump, the radial force on the impeller changes periodically. The time domain signal is transformed into a frequency domain signal, and the fundamental frequency of the impeller and the passing frequency of the blade are 101.67 Hz and 610 Hz, respectively. Conclusions: The radial force is the main cause of impeller vibration, and the transient radial force has the least dynamic impact on the impeller structure under the design condition and has a relatively large impact under the off-design condition. In order to ensure the stable operation of the centrifugal pump, it is necessary to avoid the centrifugal pump working under the non-standard flow condition, especially the small flow condition.
15 July 2022 in Proceedings of the Institution of Mechanical Engineers, Part M: Journal of Engineering for the Maritime Environment
This paper analyzed the bearing capacity of a subsea wellhead connector when exposed to external pressure and the bending moment in different operational modes and load conditions to determine the possible areas prone to failure. The contact between certain parts during the pre-tightening process impacts other areas, affecting the sealing performance. A symmetrical, three-dimensional periodic contact model was established via Finite Element Method (FEM) to simulate and analyze the sealing performance of the subsea wellhead connector. Furthermore, this study examined the variation laws governing contact form, preload, contact width, radial compression, and internal pressure, as well as their influence on the contact stress of the metal sealing ring. The results indicated that effective sealing was achieved at radial compression levels ranging from 0.1045 to 0.2089 mm. The preload contact stress was directly proportional to the preload and radial compression and inversely proportional to the contact width. The operational contact stress initially decreased, then increased at a higher internal pressure.
The subsea tree is one of the critical pieces of equipment in the subsea production system, and its installation is related to the safe production of offshore oil and gas. Due to the differences in the form of the structures, the speed of entering the water, the marine environment, and other factors, the process of the structure entering the water is exceedingly complicated. During the engineering installation, the most dangerous phase involves the structure passing through the splash zone. Based on the theory of the movement of the subsea tree passing through the splash zone, Lingshui 17-2 subsea tree installation was analyzed with the marine engineering software OrcaFlex, and a sensitivity analysis of the lowering of the subsea tree was performed. During the splash zone phase, the wave height had the highest impact on the subsea tree, affecting the horizontal offset and cable load, which may lead to the oil tree capsizing and cable breakage. Furthermore, the velocity only affected the horizontal offset, and the overall effect was not noticeable. The operational safety window for the subsea tree installation was established according to the operational safety standards. Therefore, the recommended lowering speed was 0.50 m/s, while the flow velocity should not exceed 1.50 m/s, and the wave height should not be higher than 4.5 m.
To develop an equivalent device of the umbilical cable, in which the hydraulic transmission characteristics are the same as the real umbilical cable. Simulation and experimental methods were used to study the hydraulic transmission characteristics. Theoretical relations of hydraulic resistance, hydraulic capacitance, and hydraulic inductance were derived by using the similarity principle. Simulation results showed that by comparing the valve operational time and the subsea accumulator pressure characteristics of the umbilical cable and the equivalent umbilical cable, the equivalent umbilical cable model can simulate the true umbilical valve operation characteristics. Finally, the pressure relief in the absence of an actuator or in the presence of a single actuator, was achieved by using an umbilical equivalent device. The results indicated that the umbilical equivalent device could simulate the true umbilical hydraulic transmission characteristics, making it useful for replacing the true umbilical cable in the subsea product integrity tests.
This paper proposes a new concept of an innovative deepwater production system (DPS) centred on the suspension cluster manifold (SCM), which avoids the direct impact of the seabed topography and solves the recovery problem of the traditional manifold. In this DPS, the configuration of the new steep wave riser (NSWR) is essential in achieving the stability of the SCM exposed to the loading of fluid density and ocean current. The lumped mass method was used to obtain its static configuration. The numerical model, comprising SCM and NSWR, employed the quasi-static analysis to analyse the influence of the NSWR configuration on the static stability of the SCM, and to acquire a suitable NSWR configuration. Finally, the application of this DPS was demonstrated by designing the cluster layout with six wellheads, and a coupled model was built to analyse the SCM stability. The results showed that the model exhibited excellent stability.