Poly(lactic acid) (PLA) fiber was developed more than a decade ago. It has been regarded as the most promising sustainable and biodegradable fiber to replace conventional polyethylene terephthalate (PET) polyester fiber in textile products. This paper reviews recent developments in PLA polymerization, PLA filament and fiber spinning, staple yarn spinning, fabric production, dyeing and finishing and aftercare procedures. The properties of PLA fiber are broadly similar to those of PET fiber; however, the properties of PLA fiber that differ, including thermal degradation and low hydrolytic resistance to strong alkaline, significantly affect the method selection and parameter setting of production and processing of PLA fibers and fabrics. PLA filaments are mainly produced by two-step melt spinning to get fibers with stable quality, but degradation at high temperature is still a problem. PLA staple yarns are normally spun using ring spinning. Currently existing knitting or weaving techniques can be used to produce PLA fabrics. PLA fabrics can be dyed with disperse dyes at 110°C, but their color fastness and shades are different from PET fabrics when using the same dyes. The scouring and dyeing of PLA/cotton blended fabrics and the reductive clearing after dyeing remain to be improved. As a new fiber, the entry of PLA fiber into the textile market faces difficult challenges as well as great opportunities in the future.

In this study, a three-layered composite structure based on spacer fabric was designed for absorbent wound dressings. The fabrication and selection of spacer fabrics were discussed in Part I. In this part, two selected spacer fabrics were further modified by covering a polyurethane or a polystyrene electrospun nanofibrous membrane onto their outer layer surface to form the final spacer fabric-based dressing products. In order to confirm the performance of these new spacer fabric-based dressings, the comparisons were conducted with three types of commercial wound dressings. The comparison indicators included the water contact angle, wettability, absorbency, air permeability and water vapor transmission rate. The results showed that in addition to very good water vapor and air permeability, the developed spacer fabric-based dressings had better absorbing properties than commercial foam dressings. Furthermore, their wettability was also good for application as wound dressings. The study has paved a new way to produce advanced wound dressings using three-dimensional textile structures.

Exuding wound care requires a dressing to quickly absorb exudates and properly manage moisture during the healing process. In this study, the superabsorbent spacer fabrics were designed and fabricated for application in exuding wound dressings. The fabric structure consists of three layers, including two outer hydrophobic layers made of polyester/spandex yarns and one superabsorbent middle layer made of superabsorbent yarns. In order to confirm the performance of these superabsorbent spacer fabrics, their dressing properties were tested and compared with two commercial foam dressings. The results showed that all the superabsorbent spacer fabrics had much faster wetting speeds (less than 2 s) than the foam dressings (6.04 s for Foam A and 63.69 s for Foam B). The absorbency of the superabsorbent spacer fabrics was at least twice higher than that of the foam dressings. The air permeability of the superabsorbent spacer fabrics (higher than 15 mL/s/cm² at 100 Pa) was much higher than that of the foam dressings which had a too low permeability to be measured by the testing device. In addition, the water vapor permeability, thermal insulation, and conformability of superabsorbent spacer fabrics were comparable to foam dressings. The study indicates that the superabsorbent spacer fabrics are suitable for exuding wound dressing applications.

Wearable electronic textiles (e‐textiles) are transforming personalized healthcare through innovative applications. However, integrating electronics into textiles for e‐textile manufacturing exacerbates the rapidly growing issues of electronic waste (e‐waste) and textile recycling due to the complicated recycling and disposal processes needed for mixed materials, including textile fibers, electronic materials, and components. Here, first closed‐loop recycling for wearable e‐textiles is reported by incorporating the thermal‐pyrolysis of graphene‐based e‐textiles to convert them into graphene‐like electrically conductive recycled powders. A scalable pad‐dry coating technique is then used to reproduce graphene‐based wearable e‐textiles and demonstrate their potential healthcare applications as wearable electrodes for capturing electrocardiogram (ECG) signals and temperature sensors. Additionally, recycled graphene‐based textile supercapacitor highlights their potential as sustainable energy storage devices, maintaining notable durability and retaining ≈94% capacitance after 1000 cycles with an areal capacitance of 4.92 mF cm⁻². Such sustainable closed‐loop recycling of e‐textiles showcases the potential for their repurposing into multifunctional applications, promoting a circular approach that potentially prevents negative environmental impact and reduces landfill disposal.

An ideal absorbent dressing requires high absorbency, moisture retention and antimicrobial properties. In this study, the application of silver-containing spacer fabric as an antimicrobial wound dressing was investigated. The silver distribution on the spacer fabric was different from that of layer-by-layered fabric. The middle layer of the spacer fabric contained much higher amounts of silver, while the layer-by-layered fabric had lower silver contents in its middle layers than its surface layers. The silver-containing spacer fabric could keep a better moist environment for the wound than commercial foam dressing. For the silver-containing spacer fabric, 100% reductions in viability were observed for both the Gram-positive Staphylococcus aureus and the Gram-negative Klebsiella pneumoniae after only 1 h. The spacer fabric could keep most of the silver in its middle layer and kill bacteria in the middle layer rather than at the wound contact surface. This way to absorb wound exudates and kill bacteria within the dressing reduces the silver concentration on the wound bed, and therefore this could be an efficient way to lower the potential of silver entering the human body, and prevent silver toxicity and accelerate wound healing.