Xiaobin Zhu

Prof. Dr. Xiaobin Zhu

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 February 2024 in Nanotechnology
Verified
Journal Article
Closed access
XZXiaobin Zhu
Xiaobin Zhu
ZZZhengcun Zhou
Zhengcun Zhou
JZJinlei Zhang
Jinlei Zhang
SWShuyi Wu
Shuyi Wu
The lack of low-cost methods to synthesize large-area graphene-based materials is still an important factor that limits the practical application of graphene devices. Herein, we present a facile method for producing large-area graphene oxide-metal (GO–M) films, which are size controllable and transferable. The sensor constructed using the GO–M film exhibited humidity sensitivity while being unaffected by pressure. The relationship between the sensor’s resistance and relative humidity followed an exponential trend. The GO–Mg sensor was the most sensitive among all the tested sensors. The facile synthesis of GO–M films will accelerate the widespread utilization of graphene-based materials.

20 May 2026 in Metals
Verified
Journal Article
Open access
PDF file
SGSuyi Gu
Suyi Gu
XZXiaobin Zhu
Xiaobin Zhu
QWQiang Wang
Qiang Wang
In this paper, a ternary Tb65Co25Ni10 amorphous tape was successfully prepared, and the glass forming ability (GFA), magnetic properties, and magnetocaloric characteristics of the amorphous tape were studied in detail. The values of the reduced glass transition temperature Trg, parameter γ and critical section thickness Zc indicate the good GFA of the Tb65Co25Ni10 amorphous tape. The Tb65Co25Ni10 amorphous tape exhibits spin-glass-like behavior, with a Curie temperature of 83 K and a spin-freezing temperature (Tf) of 73 K, and a large coercivity below Tf. The spin-glass-like behavior significantly deteriorates the magnetic entropy change (−∆Sm) of the Tb65Co25Ni10 amorphous tape at low temperatures, resulting in the deviation of magnetic entropy change behavior from the predicted results. However, the Tb65Co25Ni10 amorphous tape still shows an excellent magnetocaloric effect (the peak value of −∆Sm of 9.46 J kg−1 K−1 and the refrigeration capacity of 569.5 J kg−1 under 5 T, both of which are higher than those of most other heavy rare earth-based amorphous alloys), indicating the great application potential in the field of magnetic refrigeration for the amorphous tape.

10 September 2021 in Physical Chemistry Chemical Physics
Verified
Journal Article
Closed access
PDF file
SWS. Y. Wu
S. Y. Wu
RQR. L. Qian
R. L. Qian
CMChunlan Ma
Chunlan Ma
YSYun Shan
Yun Shan
YWY. J. Wu
Y. J. Wu
FHFang Hong
Fang Hong
Multifunctional probes with integrated photoluminescence and magnetism characteristics are synthesized, which are promising candidates for biomedical applications.

29 August 2024 in Physica Scripta
Verified
Journal Article
Closed access
XZXiaobin Zhu
Xiaobin Zhu
ZZZhengcun Zhou
Zhengcun Zhou
XLXu Liu
Xu Liu
YYYifei Yang
Yifei Yang
Compared with the bulk g-C3N4, g-C3N4 nanosheets have the advantages such as larger specific surface area and more active sites, making them more promising in optoelectronic applications. However, the current methods for preparing g-C3N4 nanosheets have some disadvantages such as low yield, long exfoliation time and high energy consumption. Herein, a two-step mechanochemical method combining wet ball milling with ultrasonic-ball milling has been proposed, with a high yield of up to 31.8% for suspensible g-C3N4 nanosheets. Adding YSZ balls during the ultrasound process can effectively improve the cutting efficiency of the g-C3N4 sheets, thereby increasing the yield of the suspensible nanosheets. The stability of g-C3N4 suspensions were relatively high, and the concentration of the suspensions remained above 87% after standing 24 h. The spectra of the nanosheets obtained through the two-step process had a single emission peak of 435 nm, which was suitable for photoluminescence detection.

29 November 2025 in Materials Science
Verified
Journal Article
Open access
PDF file
JDJie DU
Jie DU
XZXiaobin Zhu
Xiaobin Zhu
XWXingfu Wang
Xingfu Wang
ZZZhengcun Zhou
Zhengcun Zhou
Effect of chemical composition and isothermal treatment duration on nano-bainite steels is investigated in this work. The steels that contain Co, V and Al elements with high C are designed and produced. The nano-bainite microstructures can be obtained by the isothermal treatment in the Co and Al co-alloyed sample. Its mechanical properties and wear resistance performance are tested. Its microstructures were detected using a FESEM. After the steel is austensitized at 950 ℃ for 30 minutes and is subsequently isothermally-treated at 260 ℃ for 2 hours, the nano-bainite structures can be obtained, whose microstructures also contain martenite and residual austenite in addition to nano-bainite. The isothermal time of 120 minutes is enough to obtain sufficient nano-bainite, which forms due to the addition of both Al and Co, which accelerate the austenite → bainite transformation, since Al and Co increase the free-energy difference between ferrite and austensite and the reaction rate for obtaining nano-bainites. The fracture toughness of the nano-bainite steel obtained by the isothermal transition is obviously better than the quenching + tempering steel for the Co and Al co-alloyed sample. The fracture morphology of the Charpy impact test shows that the fracture is ductile. Although nano-bainite steel has the poor wear-resistance performance the initial stage compared to quenching + tempering steel, it shows more and more wear resistance performance with increasing wear time.