Thermal damage is one of the principle modes of wagon railway wheels. A new bainitic railway wheel steel with high thermal damage resistance and good combination of strength, plasticity, and toughness was developed. Microstructure and mechanical properties of the new steels in a tempered condition at different temperatures were examined. Microstructures were observed using scanning electron microscope and transmission electron microscope. Mechanical properties were evaluated by tensile, hardness, and Charpy impact tests with a simultaneous comparison to pearlitic railway wheel steel. The characteristic of retain austenite and V(C,N) were measured through X-ray diffractometry and energy disperse spectroscopy. The results indicate that this new bainitic wheel steel presents a submicron-sized carbide-free bainite morphology and preferable integrated mechanical properties when tempered at 280–360 °C. Precipitation strengthening plays an important role for the high strength, since a two-time-strengthening mechanism of the yield strength led by precipitation has been found at 280–360 and 480–560 °C, respectively. Compared with a pearlitic railway wheel steel, bainitic wheel steel tempered at 320 °C has a 10% higher yield strength, five times higher impact toughness, and much better thermal damage resistance, which is a promising railway wheel material for higher speed or heavier axle-load service conditions.
Tailored properties hot forming of 38MnB5Nb by partition cooling can be configured on-demand. A gradient distribution microstructural characteristic can be generated by undertaking an appropriate cooling-tempering process for the regions with different properties requirements before forming. A unified viscoplastic constitutive model coupled with the primary cooling temperature and related material constants is established based on genetic algorithm. Meanwhile, the use of the mixture of jet air and dry ice particles to cool the partition region is essential to achieve different primary cooling temperatures. In this paper, the inverse heat conduction problem is solved to obtain the relationship between the interfacial heat transfer coefficient and different cooling conditions in the partition cooling process. The U-shaped part is taken as an example to simulate the change of temperature, stress-strain, thickness, and spring-back in the process of partition cooling and tailored hot forming properties. The results show that the gradient microstructural characteristic formed by partition cooling has a great influence on the stress field distribution. The maximum stress of 345 MPa can be reached after complete pressure holding in the partition slow cooling tailored properties of the hot forming process. The maximum stress can reach 743 MPa in the partition fast cooling tailored properties of the hot forming process due to the relatively high deformation resistance of the tempered martensite at the bottom center. The maximum residual stress in the two processes after spring-back drops to 305 MPa and 545 MPa, respectively. The spring-back is small under the two processes, with a maximum spring back angle of no more than 1°.
In this paper, we have studied the influence of deformation on the microstructure and mechanical properties of 20Mn2SiCrNi bainitic high strength steel processed through a hot rolling route. Simulation of different temperatures and degrees of deformation was carried out via Gleeble-1500. The study suggested that grain size is refined when the deformation is carried out at lower temperature (> Ac3). When the degree of deformation was increased from 20% to 60%, grain size and microstructure were both refined and the size of retained austenite was reduced. The tensile strength increased from 1345 MPa to 1432 MPa. The impact toughness increased from 115 J/cm2 to 210 J/cm2 at room temperature, from 63 J/cm2 to 142 J/cm2 at −40 °C. Furthermore, it was observed that the microstructure after air cooling was composed of granular bainite (GB), lath bainite (LB) and martensite/austenite (MA) island for different deformation conditions. The study reveals that the impact toughness of 20Mn2SiCrNi bainitic high strength steel can be increased by increasing the degree of deformation.
Nodes made from steel are widely applicable to the structure of pipe racks. In this paper, the Cu content and tempering temperature of 420 MPa grade (yield strength grade) steel alloyed with Cu were studied for their effect on strength and toughness. The precipitation behavior of different Cu contents during the normalizing cooling and tempering process of the steel, and the corresponding strength and toughness levels, were clarified. The research results showed that an experimental steel with ferrite as the matrix was prepared by the normalizing and tempering method. A strengthening method mainly based on Cu precipitation was proposed, which effectively promoted the steel to have a good toughness reserve while meeting the strength requirements. With the increase in Cu content, the contribution of Cu particle precipitation to strength gradually slowed down, mainly due to the weakening of the contribution of Cu particle growth and coarsening to precipitation strengthening.