This work presents the first comprehensive investigation of phonon-electron interactions in bulk acoustic standing wave (BAW) resonators made from piezoelectric semiconductor (PS) materials. We show that these interactions constitute a significant energy loss mechanism and can set practical loss limits lower than anharmonic phonon scattering limits or thermoelastic damping limits. Secondly, we theoretically and experimentally demonstrate that phonon-electron interactions, under appropriate conditions, can result in a significant acoustic gain manifested as an improved quality factor (Q). Measurements on GaN resonators are consistent with the presented interaction model and demonstrate up to 35% dynamic improvement in Q. The strong dependencies of electron-mediated acoustic loss/gain on resonance frequency and material properties are investigated. Piezoelectric semiconductors are an extremely important class of electromechanical materials, and this work provides crucial insights for material choice, material properties, and device design to achieve low-loss PS-BAW resonators along with the unprecedented ability to dynamically tune resonator Q.
8 June 2020 in Journal of Microelectromechanical Systems
In this paper, we present ultra-high quality factor (Q) SAW resonators fabricated on aluminum gallium nitride on gallium nitride on silicon (AlGaN/GaN/Si) heterostructures with Q exceeding 6000 at room temperature. We characterize their temperature response in a broad range of temperature (-196°C to 500°C or 77 K to 773 K). The effect of doping on the Q and temperature coefficient of frequency (TCF) of the GaN-based SAW resonators is analyzed, for the first time, using un-intentionally doped GaN (UID-GaN), carbon doped GaN (C-doped), and Si doped GaN. The Q value for UID-GaN and C-doped GaN is similar and decreases from 2000 to 1000 as the temperature is increased from 77 K to 773 K. The Q value of Si-doped GaN is higher than UID and C-doped GaN by a factor of 3 (6622 at 77 K) and decreases with increase of temperature. This value of Q at 1.8 GHz is the highest reported amongst aluminum nitride (AlN) or GaN-based SAW resonators. For extreme high temperatures (≥573 K) the TCF value is half the TCF value of UID and C-doped GaN, which shows the possibility of engineering the TCF by tuning the doping concentration. For low temperatures (≤150 K) C-doped and UID-GaN show a turn over point in TCF curve which shows their promise for cold clocks. [2020-0163]
3 November 2016 in Journal of Micromechanics and Microengineering
We report on the device structure and performance of germanium telluride phase change material based ohmic RF switches. Two main types of the phase change switches using direct and indirect heating methods have been designed, fabricated and measured to analyze and compare the performance of germanium telluride in RF switch applications. Both types of switches are proven to have an insertion loss of less than 0.6 dB and an isolation of more than 13 dB for up to 20 GHz. Good linearity and power handling capability results are also measured. A reconfigurable bandpass filter using the indirectly heated phase change switch has also been developed, and shows promising performance. Efforts have been made to further analyze the issues with switching reliability, and explore possible ways of improving the performance of phase change RF switches.
2 June 2015 in Journal of Microelectromechanical Systems
In this paper, design, analysis, and implementation of a piezoelectric microelectromechanical systems (MEMS) oscillator on an ovenized microplatform is presented. An oxide-refill process is used to compensate the first-order temperature coefficient of frequency of MEMS resonators, as well as to realize thermal isolation structures. The technology enables fabrication of low-power ovenized device fusion platforms using standard silicon on insulator wafers. Utilizing the intrinsic frequency-temperature characteristic of two MEMS resonators, temperature sensing and closed-loop oven-control is realized by phase-locking two MEMS oscillators at an oven-set temperature. The design of the phase-lock control loop is studied using multidomain linear models. Control loop dynamics, noise properties, and nonideal effects are analyzed. Low-power and low-noise phase-locked loop-based control circuitry is designed in 0.18-μm CMOS to interface with the MEMS resonators. Using the developed technology, an oven controlled MEMS oscillator exhibits an overall frequency drift of <;8 ppm over -40 °C to 70 °C without the need for system calibration. In addition, the MEMS oscillators exhibit near zero phase noise degradation in closed-loop operation.
5 September 2023 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
We report on the first experimental demonstration of five self-sustaining feedback oscillators referenced to a single multimode resonator, using piezoelectric aluminum nitride on silicon (AlN/Si) microelectromechanical systems (MEMS) technology. Integrated piezoelectric transduction enables efficient readout of five resonance modes of the same AlN/Si MEMS resonator, at 10MHz, 30MHz, 65MHz, 95MHz, and 233MHz with quality ( Q ) factors of 18600, 4350, 4230, 2630, and 2138, respectively. Five stable self-sustaining oscillators are built, each referenced to one of these high- Q modes, and their mode-dependent phase noise and frequency stability (Allan deviation) are measured and analyzed. The 10, 30, 65, 95 and 233MHz oscillators exhibit low phase noise of -116, -100, -105, -106 and -92dBc/Hz at 1kHz offset frequency, respectively. The 65MHz oscillator yields Allan deviation of 4×10 -9 and 2×10 -7 at 1s and 1000s averaging time, respectively. The 10MHz oscillator’s low phase noise holds strong promise for clock and timing applications. The five oscillators’ overall promising performance also suggests suitability for multimode resonant sensing and tracking. This work also elucidates mode dependency in oscillator noise and stability, one of the key attributes of mode-engineerable resonators.
This letter reports the first results on a new generation of anti-symmetric lamb wave devices using a simple solidly mounted platform of AlN/Mo/Si and operating at very high to super high frequency (VHF-SHF) range. AlN/Mo/Si based solidly mounted resonators (SMRs) with sub-micron interdigitated transducers (IDTs) were fabricated using electron beam (ebeam) lithography and liftoff process. Plasma etching was used to etch vias in ground pads to get access to the bottom electrode for grounding. By comparing the floating, grounded and no bottom electrode device performances, it has been observed that the presented SMR design with grounded bottom electrode result in enhancement of the coupling efficiency by 500% as compared to conventional SAW devices. Additionally, these devices are more mechanically robust and can be monolithically integrated with a CMOS platform without requiring complex packaging processes as compared to conventional released lamb wave resonators.