Savannah Eisner

Ms. Savannah Eisner

Stanford University
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 May 2023 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
MYMengyang Yuan
Mengyang Yuan
JNJohn Niroula
John Niroula
QXQingyun Xie
Qingyun Xie
NRNITUL Rajput
NITUL Rajput
Kai FuKai Fu
Kai Fu
TPTomas Palacios
Tomas Palacios
This letter reports an enhancement-mode (E-mode) GaN transistor technology which has been demonstrated to operate in a simulated Venus environment (460 °C, ~ 92 atm., containing CO 2 /N 2 /SO 2 etc.) for 10 days. The robustness of the W/p-GaN-gate AlGaN/GaN high electron mobility transistor (HEMT) was evaluated by two complementary approaches, (1) in-situ electrical characterization, which revealed proper transistor operation (including E-mode ${V}_{\textit {TH}}$ with $ < {0}.{09}$ V variation) in extreme environments; and (2) advanced microscopy investigation of the device after test, which highlighted the effect of the stress conditions on the epitaxial and device structures. To the best of the authors’ knowledge, this is the first demonstration and comprehensive analysis of E-mode GaN transistors in such harsh environments, therefore establishing the proposed GaN technology as a strong contender for harsh environment mixed-signal electronics.

8 June 2020 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
AQAfzaal Qamar
Afzaal Qamar
Savannah EisnerSavannah Eisner
Savannah Eisner
Debbie SeneskyDebbie Senesky
Debbie Senesky
MRMina Rais-Zadeh
Mina Rais-Zadeh
In this paper, we present ultra-high quality factor (Q) SAW resonators fabricated on aluminum gallium nitride on gallium nitride on silicon (AlGaN/GaN/Si) heterostructures with Q exceeding 6000 at room temperature. We characterize their temperature response in a broad range of temperature (-196°C to 500°C or 77 K to 773 K). The effect of doping on the Q and temperature coefficient of frequency (TCF) of the GaN-based SAW resonators is analyzed, for the first time, using un-intentionally doped GaN (UID-GaN), carbon doped GaN (C-doped), and Si doped GaN. The Q value for UID-GaN and C-doped GaN is similar and decreases from 2000 to 1000 as the temperature is increased from 77 K to 773 K. The Q value of Si-doped GaN is higher than UID and C-doped GaN by a factor of 3 (6622 at 77 K) and decreases with increase of temperature. This value of Q at 1.8 GHz is the highest reported amongst aluminum nitride (AlN) or GaN-based SAW resonators. For extreme high temperatures (≥573 K) the TCF value is half the TCF value of UID and C-doped GaN, which shows the possibility of engineering the TCF by tuning the doping concentration. For low temperatures (≤150 K) C-doped and UID-GaN show a turn over point in TCF curve which shows their promise for cold clocks. [2020-0163]

22 April 2024 in Applied Physics Letters
Verified
Journal Article
Open access
PDF file
QXQingyun Xie
Qingyun Xie
JNJohn Niroula
John Niroula
NRNITUL Rajput
NITUL Rajput
MYMengyang Yuan
Mengyang Yuan
SLShisong Luo
Shisong Luo
TPTomas Palacios
Tomas Palacios
This Letter reports the device and material investigations of enhancement-mode p-GaN-gate AlGaN/GaN high electron mobility transistors (HEMTs) for Venus exploration and other harsh environment applications. The GaN transistor in this work was subjected to prolonged exposure (11 days) in a simulated Venus environment (460 °C, 94 bar, complete chemical environment including CO2/N2/SO2). The mechanisms affecting the transistor performance and structural integrity in harsh environment were analyzed using a variety of experimental, simulation, and modeling techniques, including in situ electrical measurement (e.g., burn-in) and advanced microscopy (e.g., structural deformation). Through transistor, Transmission Line Method (TLM), and Hall-effect measurements vs temperature, it is revealed that the mobility decrease is the primary cause of reduction of on-state performance of this GaN transistor at high temperature. Material analysis of the device under test (DUT) confirmed the absence of foreign elements from the Venus atmosphere. No inter-diffusion of the elements (including the gate metal) was observed. The insights of this work are broadly applicable to the future design, fabrication, and deployment of robust III-N devices for harsh environment operation.

29 December 2020 in Sensors
Verified
Journal Article
Open access
PDF file
Savannah EisnerSavannah Eisner
Savannah Eisner
CCCailin A. Chapin
Cailin A. Chapin
RLRuochen Lu
Ruochen Lu
Yansong YangYansong Yang
Yansong Yang
SGSongbin Gong
Songbin Gong
Debbie SeneskyDebbie Senesky
Debbie Senesky
This paper reports the high-temperature characteristics of a laterally vibrating piezoelectric lithium niobate (LiNbO3; LN) MEMS resonator array up to 500 °C in air. After a high-temperature burn-in treatment, device quality factor (Q) was enhanced to 508 and the resonance shifted to a lower frequency and remained stable up to 500 °C. During subsequent in situ high-temperature testing, the resonant frequencies of two coupled shear horizontal (SH0) modes in the array were 87.36 MHz and 87.21 MHz at 25 °C and 84.56 MHz and 84.39 MHz at 500 °C, correspondingly, representing a −3% shift in frequency over the temperature range. Upon cooling to room temperature, the resonant frequency returned to 87.36 MHz, demonstrating the recoverability of device performance. The first- and second-order temperature coefficient of frequency (TCF) were found to be −95.27 ppm/°C and 57.5 ppb/°C2 for resonant mode A, and −95.43 ppm/°C and 55.8 ppb/°C2 for resonant mode B, respectively. The temperature-dependent quality factor and electromechanical coupling coefficient (kt2) were extracted and are reported. Device Q decreased to 334 and total kt2 increased to 12.40% after high-temperature exposure. This work supports the use of piezoelectric LN as a material platform for harsh environment radio-frequency (RF) resonant sensors (e.g., temperature and infrared) incorporated with high coupling acoustic readout.

11 August 2020 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
KDKaren M. Dowling
Karen M. Dowling
TLTanya Liu
Tanya Liu
HAHannah S. Alpert
Hannah S. Alpert
CCCaitlin A. Chapin
Caitlin A. Chapin
Savannah EisnerSavannah Eisner
Savannah Eisner
Debbie SeneskyDebbie Senesky
Debbie Senesky
This article presents GaN two-dimensional electron gas (2DEG) Hall plates with low residual offset and noise at 3 V input bias. We studied devices made from three consecutive fabrication generations through current spinning offset measurements in a zero-field chamber. When operated above 1 V, the first-generation devices charted high residual offsets 1 mT. We reduced these residual offsets by three orders of magnitude in later device generations. Two experiments were performed to confirm the improvements. First, the GaN 2DEG Hall-effect plates were measured with infrared microscopy during current spinning to investigate current crowding and Joule heating. The low offset devices had minimal thermal gradients while the high offset devices had large thermal variations during current spinning. Second, zero-field current spinning was used to compare GaN 2DEG Hall-effect plates against typical commercial silicon Hall-effect plates. The Si devices had residual offsets 10μT biased at 3 V and AlGaN/GaN devices had residual offset c4 μT at 3 V, and an InAlN/GaN devices operated at 2 V had a residual offset c4 μT. Thus, for the first time, GaN 2DEG Hall-effect plates were shown to operate with high bias with low offsets and noise, which enables high fidelity sensing applications in extreme environments.

23 November 2021 in IEEE Sensors Journal
Verified
Journal Article
Closed access
ALAnand Vikas Lalwani
Anand Vikas Lalwani
AYAnanth Saran Yalamarthy
Ananth Saran Yalamarthy
HAHannah S. Alpert
Hannah S. Alpert
MHMaximillian Holliday
Maximillian Holliday
Savannah EisnerSavannah Eisner
Savannah Eisner
Debbie SeneskyDebbie Senesky
Debbie Senesky
Accurately sensing AC magnetic field signatures poses a series of challenges to commonly used Hall-effect sensors. In particular, induced voltage and lack of high-frequency spinning methods are bottlenecks in the measurement of AC magnetic fields. We describe a magnetic field measurement technique that can be implemented in two ways: 1) the current driving the Hall-effect sensor is oscillating at the same frequency as the magnetic field, and the signal is measured at the second harmonic of the magnetic field frequency, and 2) the frequency of the driving current is preset, and the measured frequency is the magnetic field frequency plus the frequency of the current. This method has potential advantages over traditional means of measuring AC magnetic fields used in power systems (e.g., motors, inverters), as it can reduce the components needed (subsequently reducing the overall cost and size) and is not frequency bandwidth limited by current spinning. The sensing technique produces no induced voltage and results in a low offset, thus preserving accuracy and precision in measurements. Experimentally, we have shown offset voltage values between 8 and $27 ~\mu \text{T}$ at frequencies ranging from 100 Hz to 1 kHz, validating the potential of this technique in both cases.