Three-dimensional braided composite has a unique spatial network structure that exhibits the characteristics of high delamination resistance, damage tolerance, and shear strength. Considering the characteristics of braided structures, two types of high-performance materials, namely, aramid and carbon fibers, were used as reinforcements to prepare braided composites with different hybrid structures. In this study, the longitudinal and transverse shear properties of 3D braided hybrid composites were tested to investigate the influences of hybrid and structural effects. The damage characteristics of 3D braided hybrid composites under short beam shear loading underwent comprehensive morphological analysis via optical microscopy, water-logging ultrasonic scanning, and X-ray micro-computed tomography methods. It is shown that the shear toughness of hybrid braided composite has been improved at certain degrees compared with the pure carbon fiber composite under both transverse and longitudinal directions. The hybrid braided composites with aramid fiber as axial yarn and carbon fiber as braiding yarn exhibited the best shear toughness under transverse shear loading. Meanwhile, the composites with carbon fiber as axial yarn and aramid fiber as braiding yarn demonstrated the best shear toughness in the longitudinal direction. Due to the different distribution of axial and braiding yarns, the transverse shear property of hybrid braided structure excels over the longitudinal shear property. The failure modes of the hybrid braided composite under the two loading directions are considerably different. Under transverse loading, the primary failure mode of the composites is yarn fracture. Under longitudinal loading, the primary failure modes are resin fracture and fiber slip. The extensive interfacial effects and the good deformation capability of the hybrid braided composites can effectively prevent the longitudinal development of internal cracks in the pattern, improving the shear properties of braided composites.
The present work focuses on the in-plane shear respond and failure mode of large size honeycomb sandwich composites which consist of plain weave carbon fabric laminate skins and aramid paper core. A special size specimen based on a typical element of aircraft fuselage was designed and manufactured. A modified in-plane shear test method and the corresponding fixture was developed. Three large size specimens were tested. The distributed strain gauges were used to monitor the mechanical response and ultimate bearing capacity. The results show that a linear respond of displacement and strain appears with the increase of the load. The average shear failure load reaches 205.68 kN with the shear failure occurring on the face sheet, and the maximum shear strain monitored on the composite plate is up to 16,115 με. A combination of theoretical analysis and finite element method (FEM) was conducted to predict the shear field distribution and the overall buckling load. The out-of-plane displacement field distribution and in-plane shear strain field distribution under the pure shear loading were revealed. The theoretical analysis method was deduced to obtain the variation rule of the shear buckling load. A good agreement was achieved among the experiment, theoretical analysis, and FEM results. It can be concluded that the theoretical analysis method is relatively conservative, and the FEM is more accurate in case of deformation and strain. The results predicted by h element and p element methods are very close. The results of the study could provide data support for the comprehensive promotion of the design and application of honeycomb sandwich composites.
This paper reported the tensile failure strengths and damage procedure of composite laminate manufactured from the toughened-epoxy T800 prepreg at multi-scale levels. According to the exterior and interior distinction of each layer in laminate, the macro/mesoscale representative volume element (macro-RVE, meso-RVE) was first constructed, respectively. Then the micro-scale representative volume element (micro-RVE) with a hexagonal fiber-packed pattern in the interior zone of each layer in the laminate was finally determined on the principle of the same fiber volume fraction between the composite laminate and multi-scale RVEs. In the multi-RVEs analysis, the mechanical failure strengths of each scale model were transmitted from the last-scale model’s homogenization, such as the meso-RVE from micro-RVE and the macro-RVE from meso-RVE. Based on our previous report, the innovative multi-scale damage and post-damage models on the concept of the smear crack were improved fully and incorporated by user-defined material subroutines (UMATs), such as in the addition of multiple cracks co-coupled, which makes it predict the element damage procedure. The averaged mechanical responses with damage mechanism of multi-scale RVEs under tensile, compressive, or shear loadings were obtained wholly by the homogenization method. The macroscale tensile damage initiation and propagation procedure were analyzed in detail including their global/local responses, being extended to comparison with experimental results.
14 October 2020 in International Journal of Aerospace Engineering
An optimization technique called shape-linked optimization, which is different from the traditional optimization method, is introduced in this paper. The research introduces an updated wing optimization design in an effort to adapt to continuous structure changes and shapes while optimizing for a lighter weight of the structure. The changing tendencies of the thickness of wing skins and the cross-section areas of the wing beams are fitted to continuous polynomial functions, whose coefficients are designed as variables, which is a different engineering approach from the size variants of the thickness and the area in the traditional optimization. The structural strength, stiffness, and stability are constraints. Firstly, this research unearths the significance of utilizing a modernized optimization process which alters the production of the traditional 12 or over 12 segment wing design and applies new approaches and methods with less variables that contribute to expedited design cycles, decreased engineering and manufacturing expenditures, and a lighter weight aircraft with lower operating costs than the traditional design for the operators. And then, this paper exemplifies and illustrates the validity of the above claims in a detailed and systematic approach by comparing traditional and modernized optimization applications with a two-beam wing. Finally, this paper also proves that the new optimized structure parameters are easier than the size optimization to process and manufacture.
14 September 2022 in The International Journal of Advanced Manufacturing Technology