Hossein Haji Agha Alizade

Hossein Haji Agha Alizade


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 July 2020 in Biofuels
Verified
Journal Article
Closed access
BSBehdad Shadidi
Behdad Shadidi
HAHossein Haji Agha Alizade
Hossein Haji Agha Alizade
GNGholamhassan Najafi
Gholamhassan Najafi
In this research, the second law of thermodynamics was employed to analyze the exergy of a diesel engine fueled with diesel–biodiesel blends (B5 and B10) and hybrid nanocatalyst additives at three concentrations (30, 60 and 90 ppm), containing cerium oxide and molybdenum oxide on amide-functionalized multiwall carbon nano tubes (MWCNTs). The research engine was a single-cylinder, four-stroke, direct-injection, air-cooled diesel engine. The exergy analysis was performed under full load conditions, at four engine speeds (1700, 2100, 2500 and 2900 rpm). The results revealed that by increasing the amount of nanocatalysts (CeO2-MWCNTs and MoO3-MWCNTs) in the fuel blends, the net exergy work rate of the diesel engine increased for both fuel blends (B5 and B10). The maximum net exergy work rate of the diesel engine was 7.71 (25.33% of total fuel exergy rate) for the B10 + 90ppm fuel blends at 2500 rpm. The exergy efficiency of the diesel engine ranged from 17.97% to 31% for B5 and 18.3% to 31.7% for B10 fuel blends, respectively. B10 containing 90 ppm nanocatalyst showed the highest exergy efficiency, at an engine speed of 1700 rpm. All fuel blends containing nanocatalyst emitted less carbon monoxide, hydrocarbon and NOx compared with nanocatalyst-free fuel blends.

11 May 2021 in Sustainability
Verified
Journal Article
Open access
PDF file
BSBehdad Shadidi
Behdad Shadidi
HAHossein Haji Agha Alizade
Hossein Haji Agha Alizade
Gholamhassan NajafiGholamhassan Najafi
Gholamhassan Najafi
Compression combustion engines are a source of air pollutants such as HC and Co, but are still widely used throughout the world. The use of renewable fuels such as ethanol, which is a low-carbon fuel, can reduce the emission of these harmful gases from the engine. A fundamental analysis is proposed in this research to experimentally examine the emission characteristics of diesel–ethanol fuel blends. Furthermore, a multi-objective genetic algorithm (e-MOGA) was developed based on the experimental data obtained to fine the most effective or Pareto set of engine emission and performance optimization solutions. So, the optimization problem had two inputs and seven objectives. For this purpose, input variables for the search space were S (rpm) varied in the range of (1600–2000) and E (%) varied in the range of (0–12). These design variables were chosen to be varied in a prespecified range with a lower and upper band as same as experimental conditions. A diesel engine using (DE2, DE4, DE6, DE8, DE10, and DE12) diesel–ethanol fuel blends, at the various speed of 1600 to 2000 rpm, was utilized for the experiment. The findings showed that the use of diesel–ethanol fuel blends decreased the concentration of CO and HC emissions by 3.2–30.6% and 7.01–16.25%, respectively, due to the high oxygen content of ethanol. As opposed to CO and HC emissions, the NOx concentration showed an increase of 7.5–19.6%. This increase was attributed to the high combustion quality in the combustion chamber, which resulted in a higher combustion chamber temperature. The optimization results confirmed that the shape of the Pareto front obtained from multi-objective ϵ-Pareto optimization could be convex, concave, or a combination of both. A new parameter was introduced as emission index or EI for selection of the best solution among the Pareto set of solutions. This parameter had a minimum value of 4.61. The variables levels for this optimum solution were as follows: engine speed = 1977 rpm, ethanol blend ratio = 10%, CO = 0.27%, CO2 = 6.81%, HC = 3 ppm, NOx = 1573 ppm, SFC = 239 g/kW·h, P = 56 kW, and T = 269.9 N·m. The EI index had a maximum value of 8.26. Conclusively, we can say that the optimization algorithm was successful in minimizing emission index for all ethanol blend ratios, especially at higher engine speeds.

1 January 2024 in International Journal of Chemical Engineering
Verified
Journal Article
Open access
PDF file
MRMohammad Rahmati
Mohammad Rahmati
MRMajid Rasouli
Majid Rasouli
HAHossein Haji Agha Alizade
Hossein Haji Agha Alizade
BABehnam Ataeiyan
Behnam Ataeiyan
All the inputs and outputs of a technical system can be interpreted from an environmental point of view. Using the life cycle assessment (LCA) approach, some changes that are less harmful to the environment can be included in the system. This research aims to evaluate the environmental effects of the wastewater treatment plant (WWTP) in South Tehran, and the LCA method was used in this study. Based on the data of qualitative parameters obtained from the measurement of Tehran province’s water and sewage company, the environmental emissions were calculated and analyzed using SimaPro software (9.0.0) and the standards defined under the ReCiPe 2016‐midpoint method. In the ReCiPe 2016 method, the results were expressed in two intermediate levels (including three classes of influence) and final (including 18). The results showed that the treated wastewater and chlorine factors had the most adverse environmental effects. Among the 18 effect classes, the treated wastewater in the class of marine environmental toxicity with the amount of 101.1531 kg 1,4‐DCB had the most environmental impacts among other classes. The power consumed by the biogas‐burning combined heat and power (CHP) unit in the wastewater treatment (WWT) process reduced the environmental effects in most impact classes. The most adverse environmental effects of the WWT process are related to damage to human health and the ecosystem. According to the findings, the use of CHP systems is suggested for energy saving and also for reducing harmful effects on the environment.

14 November 2025 in Processes
Verified
Journal Article
Open access
PDF file
MYMahtab Yarveysi
Mahtab Yarveysi
BSBehdad Shadidi
Behdad Shadidi
MHMaryam Hajjami
Maryam Hajjami
Seyed Mohammad Safieddin ArdebiliSeyed Mohammad Safieddin Ardebili
Seyed Mohammad Safieddin Ardebili
HAHossein Haji Agha Alizade
Hossein Haji Agha Alizade
Utilizing bio-based nano-fuel additives presents a promising path towards improved engine performance and reduced emissions. The response surface method is used in this investigation to predict and optimize the performance parameters and exhaust emissions of a single-cylinder diesel engine. The engine operates with B20 at 2900, 3100, and 3300 rpm and nanobiochar concentrations of 30, 60, and 90 ppm. The results showed a declining trend in all of the engine-out emissions when the nanobiochar additive was used. Based on the optimization results, an engine speed of 3108 rpm and a nanobiochar ratio of 90 ppm were found to be the optimal conditions within the defined range of the input parameters. At this point, the engine power, torque, BSFC, and emissions of NOx, CO, and UHC were measured at 5.78 kW, 17.96 Nm, and 309 g/kW·h, 104.9 ppm, 1.25 (%Vol.), and 104.9 ppm, respectively. These values represent significant improvements compared to the baseline B20 fuel. The modeling results showed that RSM could effectively predict engine performance and emissions when running on a green-based fuel like B20, with a 90 ppm nanobiochar additive.

1 April 2021
Verified
Open access
RARasoul Aydram
Rasoul Aydram
HAHossein Haji Agha Alizade
Hossein Haji Agha Alizade
MRMajid Rasouli
Majid Rasouli
BSBehdad Shadidi
Behdad Shadidi
Reduced emissions of greenhouse gases and global warming can be made possible by discovering alternative energies and reduced dependence on fossil fuels. Biogas is considered as one of the alternatives to fossil fuels. This study investigates anaerobic co-digestion for the development of biogas with sheep blood and cheese whey. Digested cow manure was used as inoculum. Using the Design Expert 10 program and within the context of mixture design, the experiments were designed. Then, 22 experimental digesters with a volume of 500 mL were considered for doing the experiments considering the design output provided by the software. Each one was filled with 300 mL of different compositions of three matters. The digesters were kept in the mesophilic temperature range (37 °C ) for 21 days. Biogas was measured using the BMP test on a daily basis. According to the experimental findings, the best composition included 35 % sheep blood, 35 % cheese whey, and 30 % inoculum. This biogas composition produced a biogas yield of 146.66 mL/g vs. The amount of methane production in this compound was 73.33 mL/g vs. After modeling, the Design Expert software predicted an optimal composition including 44 % sheep blood, 24 % cheese whey, and 32 % inoculum. Biogas yield of this prediction was 143 mL/g vs. The findings show that in order to overcome acidification in digestion of matters such as cheese whey, a composition of matters with higher pH stability can be used to increase the amount of biogas and methane produced in a particular period. Furthermore, using inoculum accelerates the digestion operations due to existence of many microorganisms and saves time and energy.

3 December 2024 in Research Square
Verified
Preprint
Open access
PDF file
NBNassim Salehi Babamiri
Nassim Salehi Babamiri
HAHossein Haji Agha Alizade
Hossein Haji Agha Alizade
MDMajid Dowlati
Majid Dowlati
Surface roughness measurements of agricultural soils play a critical role in assessing various factors, including tillage performance, surface water retention, soil resistance to rainfall-induced failure, seedbed preparation, and surface runoff management. random roughness serves as a reliable vertical index due to its ease of calculation and a margin of uncertainty of approximately ±3 mm, making it suitable for distinguishing roughness classes. Roughness measurement methods can be categorized into contact and non-contact techniques. Traditional methods often employ a stop-and-go approach, which is both tedious and time-consuming. In contrast, optical range finder sensors, when mounted on a moving system, can measure soil surface roughness in real-time, significantly reducing measurement time and increasing efficiency. This study explores both contact and non-contact measurement methods, highlighting the advantages of using optical range finder sensors mounted on a mobile system for real-time SSR assessment. Following sensor calibration, the relationship between the distances measured by the sensors and the reference pin meter method demonstrated a linear correlation under stationary conditions, with coefficients of determination (R²), mean squared error (MSE), and mean absolute percentage error (MAPE) of 0.98, 5.6, and 2.7 for the infrared (IR) sensor, and 1, 0.04, and 0.36 for the laser sensor, respectively. Both range-finder sensors effectively measured distances under stationary conditions (R² > 0.98). The performance of the IR and laser optical sensors was further evaluated on a moving system, revealing a significant effect of measurement methods and surface class (p < 0.01) on the standard deviation (SD) roughness index, while machine speed did not significantly affect the results. The interaction between measurement method and surface class was also significant (p < 0.01). The laser sensor was able to accurately detect roughness classes akin to the pin meter method at speeds below 2.6 km/h. However, at speeds exceeding 3.5 km/h, the laser sensor could only identify softer roughness classes, failing to measure roughness indices greater than 1.11 cm due to a decrease in data collection rates and the presence of larger clods in rougher classes. A strong correlation (R² > 0.9) was noted between roughness measurements from the pin meter and laser sensor at forward speeds below 3.5 km/h, while this correlation decreased to 079 at 4.8 km/h. The study suggests that utilizing laser sensors with higher data collection rates could facilitate the detection of roughness classes and enable soil profile mapping akin to the pin meter method, regardless of forward speed. Conversely, the IR method performed well only on wide and regular surfaces and struggled with irregular roughness levels, with R² values of 0.74, 0.69, 0.69, and 0.7 at forward speeds of 1, 2.6, 3.5, and 4.8 km/h, respectively. Consequently, at higher speeds, both the laser and IR sensors exhibited reduced compatibility with the pin meter method. The findings emphasize the potential of optical sensors for rapid SSR measurement, paving the way for more efficient practices in precision agriculture.