Ruibo Ren

Ruibo Ren


Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 September 2021 in Sustainability
Verified
Journal Article
Open access
PDF file
Peng WangPeng Wang
Peng Wang
HWHong-Rui Wei
Hong-Rui Wei
XLXi-Yin Liu
Xi-Yin Liu
RRRuibo Ren
Ruibo Ren
LWLi-Zhi Wang
Li-Zhi Wang
The thermal storage stability of styrene–butadiene–styrene tri-block copolymer modified bitumen (SBSPMB) is the key to avoid performance attenuation during storage and transportation in pavement engineering. However, existing evaluation index softening point difference within 48 h (ΔSP48) cannot effectively distinguish this attenuation of SBSPMB. Thus, conventional physical indexes, rheological properties, and micro-structure characteristics of SBSPMB during a 10-day storage were investigated in this research. Results showed that during long-term thermal storage under 163 °C for 10 days, penetration, ductility, softening point, recovery rate (R%), and anti-rutting factor (G*/sinδ) were decayed with storage time increasing. This outcome was ascribed to the phase separation of SBS, which mainly occurred after a 4-day storage. However, ΔSP48 after a 6-day storage met the specification requirements (i.e., below 2.5 °C). Thus, the attenuation degree of asphalt performance in field storage was not effectively characterized by ΔSP48 alone. Results from network strength (I) and SBS swelling degree tests revealed that the primary cause was SBS degradation and base asphalt aging. Moreover, conventional indexes, including penetration, ductility, and softening point, were used to build a prediction model for rheological properties after long-term storage using partial least squares regression model, which can effectively predict I, R, Jnr, G*/sinδ, and SBS amount. Correlation coefficient is above 0.8. G*/sinδ and I at the top and bottom storage locations had high coefficient with SBS amount. Thus, phase separation of SBSPMB should be evaluated during thermal storage.

5 December 2022 in Coatings
Verified
Journal Article
Open access
PDF file
SSshiqi shu
shiqi shu
CZChuanyi Zhuang
Chuanyi Zhuang
RRRuibo Ren
Ruibo Ren
BXBaodong Xing
Baodong Xing
KCkun chen
kun chen
GLGen Li
Gen Li
Water damage is one of the main forms of early damage of highway asphalt pavement, which seriously affects the service performance of asphalt pavement. To address the problem of early water damage of asphalt pavement, the addition of anti-stripping agents in asphalt is an effective technical means. To further analyze the influence of anti-stripping agents on asphalt performance, Qingchuan rock asphalt, acylamine anti-stripping agent, fatty amine anti-stripping agent, rock asphalt + acylamine anti-stripping agent and rock asphalt + fatty amine anti-stripping agent were selected to modify the base asphalt. The rheological properties of modified asphalt were tested using a dynamic shear rheometer and bending beam rheometer. Combined with the mathematical-model-fitting test results of Sigmoidal, Burgers, viscoelastic continuum damage model (VECD), etc., the effects of different anti-stripping agents on the rheological properties of asphalt were evaluated through model parameters. The results showed that the Qingchuan rock asphalt could improve the high-temperature resistance to deformation of asphalt and improved the resistance to deformation of asphalt in a wide frequency domain but increased the risk of low-temperature cracking of asphalt. Acylamine anti-stripping agents and aliphatic amine anti-stripping agents reduced the elastic recovery ability and deformation resistance under a wide frequency domain of asphalt at high temperatures but enhanced the flexible deformation and ductility of asphalt at low temperatures. The compound anti-stripping agent not only improved the high-temperature deformation resistance of asphalt, but also improved the deficiency of rock asphalt’s low-temperature performance and effectively enhanced its performance.

26 November 2010 in Mechanics of Time-Dependent Materials
Verified
Journal Article
Closed access
PDF file
LGLitao Geng
Litao Geng
RRRuibo Ren
Ruibo Ren
YZYang Zhong
Yang Zhong
QXQian Xu
Qian Xu

6 December 2019 in Polymers
Verified
Journal Article
Open access
PDF file
Peng WangPeng Wang
Peng Wang
FSFu-Quan Shi
Fu-Quan Shi
XLXi-Yin Liu
Xi-Yin Liu
RRRuibo Ren
Ruibo Ren
YZYing Zhu
Ying Zhu
LWLi-Zhi Wang
Li-Zhi Wang
The anti-cracking properties of polymer-modified asphalt depend largely on the molecular structure of the polymer modifier. However, the mysterious structure-performance relationship is still elusive. In this paper, three kinds of polymers with different chain structures were selected to address this issue. The indices of styrene, trans-butadiene, aliphatic branched-chain, and aliphatic long-chain from the infrared spectrum were used to quantify the functional group compositions of polymer modifiers. Viscoelastic parameters, including relaxation time, dissipation energy ratios, and stiffness were assessed to illustrate the anti-cracking properties of polymer-modified asphalt. Results showed that relaxation time and dissipation energy ratios were mainly determined by the polymer network strength, molecular size, aliphatic chain feature, and the orientations speed of aliphatic chains. The short relaxation time and high dissipation ratio lead to the low stiffness and favorable low-temperature performance of asphalt. The improvement of these performances requires a polymer with high indices of an aliphatic long-chain, styrene, aliphatic branched-chain, and trans-butadiene, respectively. An aliphatic-long chain, aliphatic branched-chain, and trans-butadiene were soft segments in asphalt while styrene was the rigid segment. The soft segments affect the intramolecular friction, orientation, and thermal motion at low temperatures, whereas the rigid segment enhances the strength of polymer networks. Thus, the anti-cracking property of polymer-modified asphalt can be improved by adjusting the ratio of soft and rigid segments in the polymer modifier.

1 January 2009
Verified
Conference Paper
Closed access
RRRuibo Ren
Ruibo Ren
HLHiwen Li
Hiwen Li
ZWZheren Wang
Zheren Wang
Reflective cracking is one of main distresses for cement/lime/flyash stabilized base in China. Although flexible base can be and has been utilized as sandwich layer to reduce reflecting cracks from stabilized base, the repetitive truck traffic load may cause higher tensile stress at the bottom of asphalt surface course because of large deformation from flexible base. The high tensile stress may lead to fatigue cracking. To minimize the tensile stress at the bottom of the asphalt layer and to establish optimum structures to reduce reflective cracking, nonlinear finite element technique was utilized to support three experimental pavements in Tonghua Highway in Jilin province. Base on the analyses, pavement structures 1 and 2 are recommended. In addition, for pavement structure 1, the optimal design is to include 7–12cm of AM-30, 10–15cm of flexible base, and 30–45cm of semi-rigid subbase (lime-flyash stabilized soil or cement treated base). Furthermore, for pavement structure 2, the optimal design is to include 15–20cm of flexible base, and 25–40cm of semi-rigid subbase (lime-flyash stabilized base or cement treated base).

14 May 2022 in Coatings
Verified
Journal Article
Open access
PDF file
Zhigang LiZhigang Li
Zhigang Li
KLKexin Li
Kexin Li
JZJianmin Zhang
Jianmin Zhang
RRRuibo Ren
Ruibo Ren
PDPinru Du
Pinru Du
LGLitao Geng
Litao Geng
In order to explore the influence of fine aggregate on the macro and micro properties of cold recycling mixture using emulsified asphalt (CRME), mechanical and microscopic property tests were carried out. The indirect tensile strength (ITS), unconfined compressive strength (UCS) and triaxial shear strength of different fine aggregate gradation was measured for analyzing the effects of fine aggregate on the mechanical strength, triaxial shear resistance and fracture energy of CRME. Meanwhile, the surface morphologies and air voids distribution of different CRME were observed by scanning electron microscopy (SEM) and X-ray computed tomography (X-ray CT). The results show that fine aggregate has a significant effect on the mechanical strength and shear resistance of CRME. With the same water and asphalt content, the fracture energy and failure strain of the mixture with less fine aggregate (G3-2) decreased by 16.2% and 18.2%, respectively. The less content of powder there was, the fewer cement hydration products there were due to some cement being coated by emulsified asphalt and the “cement hydration products fiber” length being shorter. Approximately 70% of the AFt hydration products in the G3-2 mixture were in the range of 1–4 μm, while those in the G1 mixture were in the range of 4–8 μm. With the increase in filler content, the number of air voids in the volume range of 0.5 mm3 ≤ V < 5 mm3 in CRME decreased, and the number of air voids in the volume range of V < 0.5 mm3 significantly increased, while the equivalent radius of air voids decreased slightly with the increase in filler content.