Some solid lubricants are characterized by a layered structure with weak (van der Waals) inter-interlayer forces which allow for easy, low-strength shearing. Solid lubricants in natural lubrication are characterized by phospholipid bilayers in the articular joints and phospholipid lamellar phases in synovial fluid. The influence of the acid–base properties of the phospholipid bilayer on the wettability and properties of the surface have been explained by studying the interfacial tension of spherical lipid bilayers based on a model membrane. In this paper, we show that the phospholipid multi-bilayer can act as an effective solid lubricant in every aspect, ranging from a ‘corrosion inhibitor’ in the stomach to a load-bearing lubricant in bovine joints. We present evidence of the outstanding performance of phospholipids and argue that this is due to their chemical inertness and hydrophilic–hydrophobic structure, which makes them amphoteric and provides them with the ability to form lamellar structures that can facilitate functional sliding. Moreover, the friction coefficient can significantly change for a given phospholipid bilayer so it leads to a lamellar-repulsive mechanism under highly charged conditions. After this, it is quickly transformed to result in stable low-friction conditions.

Our experiments aimed to study the influence of layered materials with nanometric-scale particles, which are part of lubricant oils, on their tribological properties. The object of this study was a lubricant oil made using base oil PAO4, which contained nanoparticle hexagonal boron nitride (nano h-BN) and a dispersant based on succinic acid imide. Comparative tests for engine oil (CB30) were also performed. The paper presents the method of preparing the test material and the tribological test results, including wear spot diameter (wear mark), limit wear load, and seizure load. The test results obtained demonstrate that nano-hexagonal boron nitride improves the tribological properties of lubricant oils. However, oil preparation and the quantitative selection of components markedly influence the results.

This paper presents a method for the production of high-purity anhydrous nickel(II) perrhenate. The method comprises sorption of nickel(II) ions from aqueous nickel(II) nitrate solutions, using strongly acidic C160 cation exchange resin, and subsequent elution of sorbed nickel(II) ions using concentrated perrhenic acid solutions. After the neutralization of the resulting rhenium-nickel solutions, hydrated nickel(II) perrhenate is then separated and then dried at 160 °C to obtain the anhydrous form. The resulting compound is reduced in an atmosphere of dissociated ammonia in order to produce a Re-Ni alloy powder. This study provides information on the selected properties of the resulting Re-Ni powder. This powder was used as a starting material for the production of 77W-20Re-3Ni heavy alloys. Microstructure examination results and selected properties of the produced sintered heavy alloys were compared to sintered alloys produced using elemental W, Re, and Ni powders. This study showed that the application of anhydrous nickel(II) perrhenate in the production of 77W-20Re-3Ni results in better properties of the sintered alloys compared to those made from elemental powders.

In this paper, we explain the amphoteric character of the cartilage surface by studying a lipid bilayer model built from phospholipids. We examined the interfacial tension values and molecular dynamics simulation in solutions of varying pH. The effects of negative and positive charge density (or fixed charges) on the (cartilage/cartilage) friction coefficient were investigated. In physiological (or synovial) fluid, after the isoelectric point (pI), the curve of interfacial tension decreases rapidly as it reaches pH 7.4 and then approaches a constant value at higher pH. It was shown that the curve of the interfacial tension curve exhibits a maximum value at the isoelectric point with a Gaussian shape feature. The phospholipid bilayers facilitate an almost frictionless contact in the joint. Moreover, the slippage of the bilayer and the short-range repulsion between the surfaces of the negatively charged cartilage surfaces are the main determinants of the low frictional properties of the joint.

The experiments results connected to possibilities of use of Re-Ni alloy powder for tungsten heavy alloys production were presented in the paper. This powder was obtained by nickel (II) perrhenate reduction under dissociated ammonia atmosphere. The optimal conditions for the thermal reduction for nickel (II) perrhenate were determined. The production process of investigated sinters contained, among others, cold isostatic pressing and two-staged sintering. Selected results of microstructure investigation and mechanical properties of obtained sinters were shown. Performed research indicated that the application of nickel (II) perrhenate to manufacture tungsten heavy alloys resulted in material with the microstructure typical of tungsten heavy alloys and characterized by high mechanical properties.