Studies show that the valve lift (VL) of the cam-driven hydraulic variable valve actuation (VVA) can be continuously adjusted in the range of 0–8.2 mm by controlling the opening of the throttling valve. In the present study, an orthogonal experiment with interaction was designed to analyze the effect of multi-factor coupling on the VL, valve-seating velocity (VSV), and pressure fluctuation in the valve piston cavity. In order to reduce the pressure fluctuation, the Taguchi method was applied to find the optimal combination of the key parameters including the diameter of the piston, the spring preload of the valve-seating buffer mechanism (VSBM), the spring preload of the valve, and the valve piston mass. The correctness of the VVA simulation model is verified through experiments. Moreover, the pressure fluctuation is analyzed through a numerical simulation. The obtained results showed that as long as the VSV is less than 0.5 m·s−1, the pressure fluctuations in hydraulic VVA can be reduced by several means, such as increasing the spring stiffness of the VSBM and valve, increasing the valve piston area and diameter size of the thin-walled hole, and reducing the valve piston mass and total hydraulic oil volume.
Increasing compression ratio and using lean burn are two effective techniques for improving engine performance. Methanol has a wide range of sources and is a kind of suitable fuel for a high-compression ratio spark-ignition lean burn engine. Lean burn mainly has a dilution effect, thermal effect and chemical effect. To clarify the influences of different effects and provide guidance for improving composition of dilution gases and applications of this technology, this paper chose Ar, N2 and CO2 as diluents. A spark-ignition methanol engine modified from a diesel engine with a compression ratio of 17.5 was used for the experiments. The results obtained by using methanol spark ignition combustion indicated that at engine speed of 1400 rpm and 25% load, NOx dropped by up to 77.5%, 100% and 100% by Ar, CO2 and N2. Gases with higher specific heat ratio and lower heat capacity represented by Ar exhibited the least adverse effect on combustion and showed a downward break-specific fuel consumption (BSFC) trend. Gas with high specific heat capacity represented by CO2 can decrease NOx and total hydro carbons (THC) emissions at the same time, but the BSFC of CO2 showed the worst trend, followed by N2. Gas affecting the combustion process like CO2 had chemical effect.
To simultaneously achieve high fuel efficiency and low emissions in a diesel hybrid electric vehicle (DHEV), it is necessary to optimize not only power split but also exhaust thermal management for emission aftertreatment systems. However, how to coordinate the power split and the exhaust thermal management to balance fuel economy improvement and emissions reduction remains a formidable challenge. In this paper, a hierarchical model predictive control (MPC) framework is proposed to coordinate the power split and the exhaust thermal management. The method consists of two parts: a fuel and thermal optimized controller (FTOC) combining the rule-based and the optimization-based methods for power split simultaneously considering fuel consumption and exhaust temperature, and a fuel post-injection thermal controller (FPTC) for exhaust thermal management with a separate fuel injection system added to the exhaust pipe. Additionally, preview information about the road grade is introduced to improve the power split by a fuel and thermal on slope forecast optimized controller (FTSFOC). Simulation results show that the hierarchical method (FTOC + FPTC) can reach the optimal exhaust temperature nearly 40 s earlier, and its total fuel consumption is also reduced by 8.9%, as compared to the sequential method under a world light test cycle (WLTC) driving cycle. Moreover, the total fuel consumption of the FTSFOC is reduced by 5.2%, as compared to the fuel and thermal on sensor-information optimized controller (FTSOC) working with real-time road grade information.
Combining biobutanol and oxyhydrogen in an SI engine can reduce fossil-fuel use and improve power, but oxyhydrogen increases NOx. Without sacrificing combustion stability, this work investigates lean–burn coupled with exhaust gas recirculation for a gasoline port injection + biobutanol direct injection + oxyhydrogen in-cylinder negative pressure indraft engine, across five oxyhydrogen flow levels, four exhaust gas recirculation ratios, and three excess air ratios. Results show that with lean–burn + exhaust gas recirculation, oxyhydrogen more effectively lowers the coefficient of variation of indicated mean effective pressure and increases indicated mean effective pressure, peak cylinder pressure, and peak heat release rate. With 16 L/min oxyhydrogen, the negative effects of 6–12% exhaust gas recirculation on CA 0–10 and CA 10–90 are mitigated for all excess air ratios, and the crank angle corresponding to peak pressure remains optimal under lean conditions when 6% ≤ exhaust gas recirculation ≤ 12%. Oxyhydrogen reduces CO and HC after exhaust gas recirculation, while lean–burn dominates CO reduction. Exhaust gas recirculation suppresses NO more than lean–burn. At 1.1 ≤ excess air ratios ≤ 1.2, the optimal exhaust gas recirculation is 12%, ensuring favorable in-cylinder conditions. Overall, lean–burn + exhaust gas recirculation effectively controls NO and maximizes thermal efficiency and renewable-fuel substitution. The optimal strategy is “oxyhydrogen = 16 L/min, exhaust gas recirculation = 12%, 1.1 ≤ excess air ratios ≤ 1.2”.