Yingming Zhou

Prof. Yingming Zhou

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 December 2022 in Journal of Building Engineering
Verified
Journal Article
Closed access
SWShuwei Wang
Shuwei Wang
CZChengjun Zhang
Chengjun Zhang
SZShu Zhang
Shu Zhang
YZYingming Zhou
Yingming Zhou
Muslum AriciMuslum Arici
Muslum Arici

24 May 2021 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Verified
Journal Article
Closed access
YZYingming Zhou
Yingming Zhou
GWGuozhong Wu
Guozhong Wu
Dong LiDong Li
Dong Li
WJWei Jiang
Wei Jiang
AHAhmed Kadhim Hussein
Ahmed Kadhim Hussein
ZWZemei Wang
Zemei Wang
In this study, a multi-physics coupled mathematical model was established on thermal stress distribution of double-glazed units with phase-change material (PCM-glazed) for the transient temperature fields and non-uniform intermittent solar irradiation, and the mathematical calculations are in good agreement with the experimental results, which shows that the developed model in present work can solve the coupled thermal stress distribution problem between phase change and intermittent solar irradiation in the PCM-glazed. A case that is the thermal stress distribution on the surface of glazed unit filled with paraffin under the outdoor variable temperature and non-uniform intermittent solar irradiation was studied in autumn in cold region of China. The results show that the stress produced on the surface of glazed unit filled with paraffin varies obvious, PCM layer between the glass panes significantly affects the stress values at different time, which can, respectively, reach up to about 4.59MPa and down to −3.9MPa for tensile and compressive strains once the paraffin in liquid state, due to improved thermal conductivity of PCM throughout phase transition to liquid. Additionally, the frame is the key factor causing temperature gradient of PCM-glazed unit, and the biggest tensile stress appears at the edge. The influence range of the frame on the surface temperature and stress of the PCM-glazed unit is limited and different, and the largest influence distance of the surface temperature and stress from the edge is 0.1 m and 0.03 m, respectively.

12 May 2021 in Energy Exploration & Exploitation
Verified
Journal Article
Open access
PDF file
YZYingming Zhou
Yingming Zhou
GWGuozhong Wu
Guozhong Wu
SWShuwei Wang
Shuwei Wang
BHBo Huang
Bo Huang
FWFengshun Wang
Fengshun Wang
ZWZemei Wang
Zemei Wang
The low heat transfer and high energy storage performance of phase change material (PCM) will improve the thermal performance of the PCM-glazed units. However, decreasing the heat transfer results in uneven thermal load on the surface of the PCM-glazed units, which is an important cause of thermal stress in such units, because the glass in glazed units is a fragile material, and then large thermal stress can result in cracks and possible fallout of the glazed units. To study the thermal stress distribution of PCM-glazed units, a method combined numerical simulation and experimental analysis was conducted. First, the heat transfer performance and thermal stress distribution of PCM-glazed units with PCM thicknesses between 3 and 11 mm were experimentally investigated. Results showed that the thermal performance of a glazed unit was improved by adding PCM, and the variation of thermal strain on its surface with a PCM-layer thickness of 7 mm was the smallest in five test facilities. Then, the thermal stress was numerically investigated regarding the PCM height and the aspect ratio of the PCM-glazed unit. The higher the PCM height, the greater the maximum strain. An aspect ratio of PCM-glazed units of 1.5 was recommended.

31 August 2023 in Buildings
Verified
Journal Article
Open access
SWShuwei Wang
Shuwei Wang
MZMin Zhang
Min Zhang
YSYaoyang Shi
Yaoyang Shi
LCLixin Chen
Lixin Chen
YZYingming Zhou
Yingming Zhou
This research paper explores using marine shells as coarse aggregates in producing seawater sea sand UHPC-CA. The study examined factors such as coarse aggregates (granite, oyster shell, and cone shell), fine aggregates (sea sand and river sand), fiber types, and content. The research findings indicate that different coarse aggregates and fibers influence the flow performance of UHPC-SCA. The study identified the cone shell as the best coarse shell aggregate and 1.5% steel fiber as the optimal fiber and inclusion amount. The compressive strength of this combination reached 106 MPa, which is comparable to the granite stone UHPC-CA of the same particle size.