This paper focuses on the frequency coded chipless Radio Frequency Identification (RFID) wherein the tag’s information bits are physically encoded by the resonators’ notch position which has an effect on the frequency spectrum of the backscattered or retransmitted signal of the tag. In this regard, the notch analytical model is developed to consider the notch position and quality factor. Besides, the radar cross section (RCS) mathematical representation of the tag is introduced to consider the incident wave’s polarization and orientation angles. Hence, the influences of the incident wave’s orientation and polarization mismatches on the detection performance are quantified. After that, the tag measurement errors and limitations are comprehensively explained. Therefore, approaches to measureing RCS- and retransmission-based tags are introduced. Furthermore, the maximum reading range is theoretically calculated and practically verified considering the Federal Communications Commission (FCC) Ultra Wideband (UWB) regulations. In all simulations and experiments conducted, a mono-static configuration is considered, in which one antenna is utilized for transmission and reception.

The main focus of this research paper is to develop a realistic mathematical framework to accurately characterize the performance of the harmonic identification system. This mathematical framework incorporates the essential factors that affect the harmonic identification system such as, the radiation pattern and polarization of the reader and transponder antennas, the angle of incidence and reflection, conversion efficiency of the non-linear element, besides the environmental effects which are multipath and clutter reflections. To validate the proposed analytical model, simulations and measurements are conducted using a state-of-the-art transponder equipped with a Schottky diode that exhibits non-linear characteristics in output power. The performance of the transponder is evaluated in both scenarios, with and without environmental reflections, where a significant drop in the backscattered signal is observed due to the multipath reflections. Accordingly, a Ray-tracing model is utilized to investigate the environmental reflections, and thus the system performance could be evaluated analytically. The close agreement between the results obtained from developed analytical framework and Ray-tracing simulations together with the corresponding measurements demonstrate the effectiveness of the proposed analytical framework in accurately predicting the performance of the harmonic identification systems.

Chipless radio frequency identification (RFID) technology is expected to replace barcode technology due to its ability to read in non-line-of-sight (NLOS) situations, long reading range, and low cost. Currently, there is extensive research being conducted on frequency-coded (FC) co-polarized radar cross-section (RCS)-based tags, which are widely used. However, detecting co-polarized chipless RFID tags in cluttered environments is still a challenge, as confirmed by measuring two co-polarized tags in front of a perfect metal reflector ($30.5\mathrm{cm}\times 22.5\mathrm{cm}$). To address this challenge, a realistic mathematical model for a chipless RFID system has been developed that takes into account the characteristics of the reader and the tag, as well as reflections from cluttered objects. This extensive mathematical model developed for linear chipless RFID systems in clutter scenarios holds the potential to greatly assist researchers in their exploration of RCS-based tags. By relying solely on simulations, this model provides a tool to effectively analyze and understand RCS-based tags, ultimately simplifying the process of generating more authentic tag designs. This model has been simulated and verified with measurement results by placing a single flat metal reflector behind two co-polarized one-bit designs: a dipole array tag and a square patch tag. The results showed that the interfering signal completely overlaps the ID of the co-polarized tag, severely limiting its detectability. To solve this issue, the proposed solution involves reading the tag in cross-polarization mode by etching a diagonal slot in the square patch tag. This proposed tag provides high immunity to the environment and can be detected in front of both dielectric and metallic objects.

Chipless radio frequency identification (RFID) technology is expected to replace barcode technology due to its ability to read in non-line-of-sight (NLOS) situations, long reading range, and low cost. Currently, there is extensive research being conducted on frequency-coded (FC) co-polarized radar cross-section (RCS)-based tags, which are widely used. However, detecting co-polarized chipless RFID tags in cluttered environments is still a challenge, as confirmed by measuring two co-polarized tags in front of a perfect metal reflector (30.5cm×22.5cm). To address this challenge, a realistic mathematical model for a chipless RFID system has been developed that takes into account the characteristics of the reader and the tag, as well as reflections from cluttered objects. This model has been simulated and verified with measurement results by placing a single flat metal reflector behind two co-polarized one-bit designs: a dipole array tag and a square patch tag. The results showed that the interfering signal completely overlaps the ID of the co-polarized tag, severely limiting its detectability. To solve this issue, the proposed solution involves reading the tag in cross-polarization mode by etching a diagonal slot in the square patch tag. This proposed tag provides high immunity to the environment and can be detected in front of both dielectric and metallic objects.