Protection of water environment from pollution is one of the major tasks in the contemporary world. Nowadays, in the Republic of Kazakhstan ecological situation concerning sewage treatment remains deficient. Raw sewage is often discharged directly onto filtration beds or landfills. Many existing...

Mathematical models of activated sludge process are well recognised and widely implemented by researchers since 1980’s. There is also numerous software available for modelling and simulation of activated sludge plants, but practical application of those tools is rather limited. One of the main...

Due to geographical limitations (lack of natural receivers of treated wastewater) large sewage storage ponds are the main method of sewage disposal in the Republic of Kazakhstan. The paper presents the results of research on the environmental impact of sewage ponds serving the city of Kostanay (Kazakhstan). The scope of the research included the determination of basic quality parameters of raw and treated wastewater, the analysis of the chemical composition of groundwater in the vicinity of sewage ponds, and the analysis of the water quality of the Tobol River. The obtained results showed that efficiency of treatment facilities was unsatisfactory and water quality in the ponds did not meet requirements for surface waters for fishery. Highest contamination of groundwater was observed in sampling points close to the sewage ponds and was decreasing while the distance from the ponds was increasing. Multivariate analysis of the research data indicated that sewage from storage ponds, infiltrating into the ground, may affect quality of groundwater, which in turn supplying the Tobol River may also determine the quality of the river water.

The storage of sewage sludge in landfills is still the primary method of their disposal in many countries. Therefore, finding sustainable solutions for the reuse of this waste is an important issue to be addressed. This paper presents the results of research on processing sewage sludge generated at the wastewater treatment plants of Almaty, Kazakhstan, for use in the manufacturing of ceramic bricks. The chemical composition of the sewage sludge was determined, showing the presence of 35.7% silicon dioxide, 7.3% aluminum oxide, 11.2% iron oxide, and 10.6% calcium oxide. Experimental studies established that adding sewage sludge to clay reduces the compressive strength of ceramic bricks while increasing their flexural strength. Furthermore, as the proportion of sewage sludge in the clay mixture increases, the average density of the ceramic bricks decreases, while water absorption increases. It was also found that ceramic bricks made from a mixture of 90% clay and 10% sewage sludge demonstrated the best physico-mechanical properties. This composition showed increased flexural strength and a simultaneous reduction in the average density by 15.4%, indicating the improved structural quality of the manufactured bricks.

The article presents the results of an experimental study on the clarification of biologically treated wastewater in a clarifier with a suspended sludge layer. The pilot plant was receiving effluent from trickling filters treating municipal wastewater. An experimental clarifier worked under steady-state conditions considering the influent characteristics and variable operating parameters in terms of flow velocities and height of the suspended layer. From the experimental dependences between different technological parameters it was found that the optimum range of the upward flow velocities providing a dynamic equilibrium of the suspended layer was 0.6–1.4 mm/s. Upward flow velocities below 0.5 mm/s can lead to sludge compaction at the bottom of the unit, while values greater than 1.8 mm/s may cause sludge washout. It was also found that higher suspended layer height values favor higher efficiency of the clarifier and can achieve suspended solids in the discharge of less than 5.0 mg/L; this height should be greater than 0.6 m Technological efficiency of the experimental clarifier was significantly higher than the conventional unit and was comparable with tertiary treatment technologies.

Water and energy are the main natural resources, and their rational use is the basis for sustainable development. Therefore, the energy efficiency of water supply networks is one of the priorities for the management system of water utilities. Many methods and indicators can be used to assess the energy efficiency of water distribution networks (WDNs), and their choice should be adapted to the characteristics of a WDN. This paper presents an energy audit of WDNs that are supplied from five reservoirs located above the supply area, to which water is supplied from four underground and surface water intakes. In the analysis of the system operation, a hydrodynamic computer model of the water distribution network was used to estimate the operating parameters that are necessary to determine the energy efficiency indicators. A new method for calibrating the emitter coefficient used for water loss modeling is also proposed. The conducted audit showed that more than 70% of the energy supplied to the WDS was “lost”, mainly due to friction (37%) and water losses (27%). Thanks to hydraulic modeling, it was possible to indicate that 34% of the energy lost in the system was related to the use of pressure-reducing valves (PRV), and that only 3% was directly related to friction. In turn, the majority of leaks are attributed to service connections (17.4% vs. 8.8% in the water distribution network).