Moisture damage and low-temperature cracking are common distresses experienced by road pavement. Different types of modifiers, such as fibers, can be used to improve the quality of asphalt pavements. In this paper, lignin and glass fiber were selected as additives to enhance the water- and low-temperature stability of the asphalt mixtures. The main objective of this study was to evaluate the composite effects of adding lignin fiber and glass fiber to a bituminous mix using experimental methods. The Marshall immersion, freeze–thaw splitting, and three-point bending tests were applied to evaluate the efficiency of lignin fiber (and/or) glass fiber modified asphalt mixes with regard to moisture damage and low temperature. Four kinds of asphalt mixtures, namely, the control asphalt mix (C), lignin fiber modified asphalt mix (L), glass fiber modified asphalt mix (G), and a composite of lignin fiber and glass fiber modified asphalt mix (LG) were evaluated. The experimental results showed that with the addition of 0.30% lignin fiber and 0.30% glass fiber the water stability, low-temperature stability, and quality of bituminous mix were improved significantly. With lignin fiber, the asphalt mixtures showed better resistance to thermal cracking, while glass fiber resulted in greater moisture susceptibility. The composite admixture was more effective than either lignin or glass fiber in modifying the asphalt performance. This clarifies the great beneficial effect of using the composite mixture in the asphalt mixtures industry.

Due to rapid growth of traffic density, the phenomenon of overloading on high-grade highways causes various modes of distresses to the pavement such as rutting, thermal cracking, and water damage. Modification of asphalt mixes is the most common solution to improve the performance of asphalt pavement to mitigate its damages. This paper provides a review on the influence of diatomite or lignin fiber as a modifier in asphalt mixes. In order to assess the effectiveness of selected additives on asphalt mix performance, several tests, such as wheel tracking, indirect tensile, three points bending, freeze thaw splitting, and marshall immersion, were reviewed. The review indicated that the addition of diatomite increases the high temperature rutting resistance of asphalt mixes, but some researchers observed that it has a little improvement on the low temperature performance of asphalt mixes and the optimum amount of diatomite at 12–14% of asphalt binder can be added into the mix. In contrast, lignin fiber has a significant effect on the low temperature cracking resistance of asphalt mixes; however, its influence on the high temperature rutting resistance of asphalt mix is limited, and the optimum amount of lignin fiber is 0.2–0.4% per asphalt mix composition. The review also indicated that the single additives haven’t the ability to enhance the overall performance of asphalt mix. Consequently, the utilization of double additives can improve the overall performance of asphalt mixes at the same time, but it is still in an early stage in the application of highway engineering due to all previous researches concentrated on the single modification. Moreover, this review suggests that the future use of diatomite and lignin fiber compound modified asphalt mix can improve the overall mix performance.

The performance and the fundamental weaknesses of asphalt mix under environmental temperature and water effects have made researchers try to modify the asphalt mix properties by using the proper additives. For this reason, this paper aims to improve the anti-cracking performance and water stability of asphalt pavement by adding a novel composite of diatomite and lignin fiber in asphalt mixes. Four types of asphalt mixes, including control asphalt mix (CAM), diatomite modified asphalt mix (DMAM), lignin fiber modified asphalt mix (LFMAM), and diatomite-lignin fiber composite modified asphalt mix (DLFMAM) were prepared in the laboratory. Low-temperature bending test, Marshall Immersion test, and freeze-thaw splitting test were employed to evaluate the performance of the asphalt mixes. Results reveal that the use of the lignin fiber in reinforced asphalt mixes combined with diatomite led to an enhancement in the asphalt pavement performance more than the other three types of mixes. Diatomite has an important influence on the water damage resistance of asphalt mix more than lignin fiber. On the other hand, diatomite has a small effect on the anti-cracking performance; meanwhile, lignin fiber showed a significant improvement in the cracking resistance of asphalt mixes. DLFMAM has the best traveling performances among all asphalt mixes. Thus, this work provides a good reference for the design of composite asphalt mixes.

National highway projects present a crucial role in economic growth, as they have a great influence on the national income. Therefore, the decision makers plan to construct these projects at a rapid rate. To achieve the just aforesaid, the utilization of asphalt of adequate quality and gradation is essential. The key problem which lies in recent decades is that many types of asphalt mixtures are rejected and reconstructed in the site due to the gradation variation of aggregates in the asphalt mixture which waste raw materials, cost and time. Thus, this research seeks to assess the possibility of accepting asphalt mixes with aggregates gradation variation (within the range from +4% above the upper specification limit to −2% below the lower specification limit). A wearing surface mix with gradation 3B was prepared according to the Egyptian code. The gradation variation was presented as the aggregate gradation is out of the specification limits during Hot Mix Asphalt (HMA) production. The aggregate gradations lie above and below the upper and lower specification limits, respectively, by ±2%, ±4% and ±6%. The design gradation of the control mix was included as a reference case. The different mix properties were measured using the Marshall Mix design method. Then, the performance of HMA mixes was evaluated under the effects of high temperature and water cycles through applying wheel loading tracking and Indirect Tensile Strength (ITS) tests. The results show that the 3B mixes with a gradation within a range of +4% to −2% of the upper and lower specification limits recorded the lowest rutting depth and the highest water damage resistance in hot regions compared to ordinary asphalt mixes. In summary, the new aggregate gradation limits will provide a reference for the design of asphalt mixture in hot climate regions.

The protection of concrete structures against corrosion in marine environments has always been a challenge due to the presence of a saline solution—A natural corrosive agent to the concrete paste and steel reinforcements. The concentration of salt is a key parameter influencing the rate of corrosion. In this paper, we propose an optical fiber-based salinity sensor based on bundled multimode plastic optical fiber (POF) as a sensor probe and a concave mirror as a reflector in conjunction with an intensity modulation technique. A refractive index (RI) sensing approach is analytically investigated and the findings are in agreement with the experimental results. A maximum sensitivity of 14,847.486/RIU can be achieved at RI = 1.3525. The proposed technique is suitable for in situ measurement and monitoring of salinity in liquid.

Wind turbines are one of the key systems in wind energy development. The wind tower supporting the whole wind turbine is a towering structure, which has been affected by installation, transportation, environment, and other factors. Furthermore, it is prone to experience other quality problems that would be difficult to detect for wind turbine towers. Therefore, the key to maintain the wind tower structure and to ensure the normal operation of a wind turbine is to carry out comprehensive and detailed detection and monitoring studies during its service stage. This paper sorted out several common quality problems including structural damage, deformation, flange bolts loosening, and corrosion of wind tower and relevant research on the detection and monitoring of these quality problems. In addition, some nondestructive testing technologies are introduced, including the ultrasonic phased array, time of flight diffraction, magnetic memory, acoustic emission, fiber Bragg grating and piezoelectric impedance, and applications in wind turbine towers.