Steelmaking has been experiencing continuous challenges and advances concerning process methods and control models. Integrated steelmaking begins with the hot metal, a crude liquid iron that is produced in the blast furnace (BF). The hot metal is then pre-treated and transferred to the basic lined oxygen furnace (BOF) for refining, experiencing a non-easily predictable temperature drop along the BF–BOF route. Hot metal temperature forecasting at the BOF is critical for the environment, productivity, and cost. An improved multivariate adaptive regression splines (MARS) model is proposed for hot metal temperature forecasting. Selected process variables and past temperature measurements are used as predictors. A moving window approach for the training dataset is chosen to avoid the need for periodic re-tuning of the model. There is no precedent for the application of MARS techniques to BOF steelmaking and a comparable temperature forecasting model of the BF–BOF interface has not been published yet. The model was trained, tested, and validated using a plant process dataset with 12,195 registers, covering one production year. The mean absolute error of predictions is 11.2 °C, which significantly improves those of previous modelling attempts. Moreover, model training and prediction are fast enough for a reliable on-line process control.
The classical thermal cycle in a Hot Dip Galvanizing (HDG) line has four steps: heating, soaking, cooling, and aging. The furnace of an ArcelorMittal HDG line was revamped to increase its heating capacity. This new configuration without the soaking step led to the redefinition of the thermal cycles for all the steel grades, especially for High Strength Low Alloyed (HSLA) steels, where it was necessary to define a new control parameter based on time and temperature. This paper presents the work done to improve the control of the mechanical properties of HSLA steels in the HDG line. Four different types of numerical models (linear and polynomial regressions, artificial neural networks, and Multivariate Adaptive Regression Splines), are applied to predict the yield strength and the tensile strength of individual coils. It is concluded that the introduction of the time–temperature parameter improves the accuracy of the predictions over 10% in most of the cases. An additional improvement is obtained with the use of the process values corresponding to the sampling area instead of the coil average ones. The use of these models makes it possible, if necessary, to adjust individually the presets of the coils before processing them in the galvanizing line and reduce the scattering of the mechanical properties.
13 February 2008 in European Journal of Lipid Science and Technology
Climate change is associated with global warming. This paper discusses the environmental impacts of the decarbonisation plan proposed by the Spanish Government, comparing the current situation with those foreseen for 2020 and 2030. Furthermore, climate change will vary the thermal demands of buildings. The paper thus investigates the heating and cooling demands of a type of single-family house located in eight Spanish cities with very different climates and altitude. The combined effects of the decarbonisation plan and climate change are analysed based on the environmental impacts caused by the electricity required to meet thermal demands. Both effects led to a reduction of the damage in the categories Human Health (59–68%), Climate Change (57–67%) and Resources (54–65%). However, the damage to Ecosystem Quality will increase (5–28%) as a result of the greater impact on this damage category from the energy production scenario for 2030, although thermal requirements in households will decrease.
The use of lightweight concrete for the construction of single-family houses has become increasingly popular in Spain. In this paper, single-family houses with different shape factors and window-to-wall ratios are analysed from both a thermal and environmental perspective using Passive House Planning Package (PHPP) software to calculate the energy demand. The study has been carried out for different Atlantic microclimates (coastal, inland, and mountain) in northern Spain. What most affects the thermal energy used for air conditioning is the variation of the microclimates, so the study focuses mainly on this aspect. Operational energy for heating has decreased greatly via the use of high degree of insulation and hence the next task is to decrease the total energy consumed taking into account the embodied energy. Impacts on Primary Energy and Global Warming Potential are calculated using a cradle-to-grave approach. The energy use for heating and domestic hot water is analysed for different thicknesses of insulation under three energy supply scenarios: electricity only (for 2018 and with the Spanish decarbonisation plan for 2030); heat pump plus electricity; and natural gas boiler. Even for houses with a good level of insulation, the ratio of operational-to-total impacts varies significantly: from 46% to 87% for primary energy and from 31% to 75% for global warming potential, depending on the shape factor of the house, the microclimate and the heat supply scenario. By applying future environmental policies, electricity can become a more environmentally friendly option than natural gas.