To investigate the adsorption kinetics and thermodynamic adsorption mechanism and laws of dry flue gas desulfurization, we prepared a new adsorbent by loading Cr, Cu, and Zn on TiO2-loaded multiwalled carbon nanotubes. Desulfurization experiments were also carried out. In this study, three kinds of samples were used for simulation and diffusion processes in the dynamic adsorption of different SO2 volume fractions in flue gas and thermodynamic model analysis of different temperatures in flue gas. Results show that the diffusion coefficient of SO2 in three kinds of samples ranges from 10−16 to 10−14 m2 s−1, and the diffusion may be dominated by configuration diffusion. The intraparticle diffusion model predicts that the performance improves with an increase in the SO2 volume fraction and a shift of adsorption time. This finding indicates that an increase in SO2 volume fraction and a change in adsorption time increase the Kundsen diffusion specific gravity and decrease the configuration diffusion specific gravity, thereby increasing the SO2 diffusion resistance, which becomes faster than the activation energy barrier resistance in the catalytic oxidation reaction. Thus, the diffusion resistance specific gravity increases in the total resistance of the diffusion reaction. One possible mechanism of the adsorption process is the transition to surface reaction control at the early stage of adsorption to joint control of late diffusion and surface reactions. Adsorption thermodynamics studies show that SO2 adsorption by three adsorbents is a spontaneous, exothermic, and entropic reduction process, and the increase in temperature is inconducive for SO2 adsorption in three samples.
19 January 2022 in Metallurgical and Materials Transactions B
Electromagnetic brake (EMBr) technique is adopted to reduce the turbulence of molten alloy in the slab mould in the continuous casting process, especially under high casting speed. We introduce a state-of-the-art EMBr technique by reviewing the published literature. The main objective of this paper is to give a clear view of the EMBr technique in terms of the magnet arrangement, along with their “Braking” effect to help decision-making. The EMBr system can be divided into three types, in terms of the magnet arrangement: the Local type, the Ruler type and the Multi-mode type, respectively. Both advantages and disadvantages of each type have been discussed. Further challenges are also raised.
The brake effect of the freestanding adjustable combination electromagnetic brake (FAC-EMBr) and EMBr ruler on the behavior of molten steel flow and the level fluctuation were investigated with the numerical method. The effects of the horizontal magnetic pole position (EMBr ruler), magnetic induction intensity, and casting speed on two types of electromagnetic brakes were studied. The numerical simulation results show that the magnetic field caused by the EMBr ruler is mainly distributed under the submerged entry nozzle (SEN), and it is very weak nearby the meniscus area. After the FAC-EMBr is applied, the magnetic field is mainly distributed in the area below the submerged entry nozzle, the upper roll region, and in the meniscus region. The application of the electromagnetic brake can effectively suppress the impact of the jet and decrease the molten steel velocity in the meniscus area. The brake effect of the EMBr ruler on the behavior of the molten steel flow and the level fluctuation is significantly influenced by the horizontal magnetic pole position. The increasing of the magnetic flux density can significantly increase the velocity of molten steel in the upper roll region and lead to an intense fluctuation in the steel/slag interface, as the horizontal magnetic field cannot cover the three key regions. The brake effect of the FAC-EMBr is less influenced by the variation of the process parameters due to the addition of vertical magnetic poles. Additionally, the “secondary braking effect” of the vertical magnetic poles can help to lower the increase of velocity in the upper roll region caused by the excessive magnetic induction intensity and the high casting speed. Therefore, even under the high casting speed conditions, the application of a new type of FAC-EMBr is also an efficient way to suppress the molten steel flow and level fluctuation at the meniscus area and decrease the possibility of slag entrapment.
This research aims to investigate the control effect of asymmetric flow in a slab mold using a novel magnetic field arrangement: freestanding adjustable combination electromagnetic brake (FAC-EMBr). Three scenarios (submerged entry nozzle moves to the narrow face, wide face of the slab mold, and rotates 10°) were studied using three-dimensional numerical simulation. The results show that the magnetic field generated by the FAC-EMBr system can effectively cover three key zones in mold and that the magnetic flux density in the zone cover by a vertical magnetic pole can be adjusted according to the actual flow condition. The FAC-EMBr can effectively improve the asymmetric flow in a mold and near the narrow surface caused by the asymmetric arrangement of the nozzle and can effectively inhibit the occurrence of the flow deviation phenomenon and stabilize the steel/slag interface fluctuation. At the same time, FAC-EMBr has obvious inhibition effects on the surface velocity and can optimize the asymmetric distribution of the surface velocity and the upper reflux velocity caused by the asymmetric arrangement of the nozzle. This study can provide theoretical evidence for the development and utilization of a new electromagnetic brake technology.