Saqib Hameed

Dr. Saqib Hameed

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 March 2016 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
SHSaqib Hameed
Saqib Hameed
HGHernán Alberto González
Hernán Alberto González
Antonio J. Sánchez EgeaAntonio J. Sánchez Egea
Antonio J. Sánchez Egea
AAAmelia Nápoles Alberro
Amelia Nápoles Alberro

25 May 2018 in Materials
Verified
Journal Article
Open access
PDF file
SHSaqib Hameed
Saqib Hameed
HGHernán Alberto González
Hernán Alberto González
JBJosé I. Perat Benavides
José I. Perat Benavides
AAAmelia Nápoles Alberro
Amelia Nápoles Alberro
Antonio J. Sánchez EgeaAntonio J. Sánchez Egea
Antonio J. Sánchez Egea
In this article, the influence of electropulsing on the machinability of steel S235 and aluminium 6060 has been studied during conventional and electropulsing-assisted turning processes. The machinability indices such as chip compression ratio ξ , shear plane angle ϕ and specific cutting energy (SCE) are investigated by using different cutting parameters such as cutting speed, cutting feed and depth of cut during electrically-assisted turning process. The results and analysis of this work indicated that the electrically-assisted turning process improves the machinability of steel S235, whereas the machinability of aluminium 6060 gets worse. Finally, due to electropluses (EPs), the chip compression ratio ξ increases with the increase in cutting speed during turning of aluminium 6060 and the SCE decreases during turning of steel S235.

21 September 2022 in Sensors
Verified
Journal Article
Open access
PDF file
MAMuhammad Rizwan Awan
Muhammad Rizwan Awan
HGHernán Alberto González
Hernán Alberto González
SHSaqib Hameed
Saqib Hameed
Fahid RiazFahid Riaz
Fahid Riaz
SHShahzaib Hamid
Shahzaib Hamid
AHAbrar Hussain
Abrar Hussain
Cut-off operation is widely used in the manufacturing industry and is highly energy-intensive. Prediction of specific energy consumption (SEC) using data-driven models is a promising means to understand, analyze and reduce energy consumption for cut-off grinding. The present article aims to put forth a novel methodology to predict and validate the specific energy consumption for cut-off grinding of oxygen-free copper (OFC–C10100) using supervised machine learning techniques. State-of-the-art experimental setup was designed to perform the abrasive cutting of the material at various cutting conditions. First, energy consumption values were predicted on the bases of input process parameters of feed rate, cutting thickness, and cutting tool type using the three supervised learning techniques of Gaussian process regression, regression trees, and artificial neural network (ANN). Among the three algorithms, Gaussian process regression performance was found to be superior, with minimum errors during validation and testing. The predicted values of energy consumption were then exploited to evaluate the specific energy consumption (SEC), which turned out to be highly accurate, with a correlation coefficient of 0.98. The relationship of the predicted specific energy consumption (SEC) with material removal rate agrees well with the relationship depicted in physical models, which further validates the accuracy of the prediction models.

21 March 2019 in Materials
Verified
Journal Article
Open access
PDF file
AAAmelia Nápoles Alberro
Amelia Nápoles Alberro
HGHernán Alberto González
Hernán Alberto González
Antonio J. Sánchez EgeaAntonio J. Sánchez Egea
Antonio J. Sánchez Egea
SHSaqib Hameed
Saqib Hameed
RAReyna M. Peña Aguilar
Reyna M. Peña Aguilar
Grinding energy efficiency depends on the appropriate selection of cutting conditions, grinding wheel, and workpiece material. Additionally, the estimation of specific energy consumption is a good indicator to control the consumed energy during the grinding process. Consequently, this study develops a model of material-removal rate to estimate specific energy consumption based on the measurement of active power consumed in a plane surface grinding of C45K with different thermal treatments and AISI 304. This model identifies and evaluates the dissipated power by sliding, ploughing, and chip formation in an industrial-scale grinding process. Furthermore, the instantaneous positions of abrasive grains during cutting are described to study the material-removal rate. The estimation of specific chip-formation energy is similar to that described by other authors on a laboratory scale, which allows to validate the model and experiments. Finally, the results show that the energy consumed by sliding is the main mechanism of energy dissipation in an industrial-scale grinding process, where it is denoted that sliding energy by volume unity decreases as the depth of cut and the speed of the workpiece increase.

12 May 2019 in Metals
Verified
Journal Article
Open access
PDF file
Daniel Martinez KrahmerDaniel Martinez Krahmer
Daniel Martinez Krahmer
SHSaqib Hameed
Saqib Hameed
Antonio J. Sánchez EgeaAntonio J. Sánchez Egea
Antonio J. Sánchez Egea
DPD. Pérez
D. Pérez
JAJAVIER CANALES ABAITUA
JAVIER CANALES ABAITUA
Luis Norberto López De LacalleLuis Norberto López De Lacalle
Luis Norberto López De Lacalle
Free-cutting steels are developed to produce large quantities of parts with low mechanical behavior, mainly for automotive sector. These alloys contain phosphorous, lead, sulfur, and manganese that help to improve the machinability and surface roughness. However, due to the toxicity of lead, steel mills in recent years have been focusing on non-toxic steels to produce minimum environmental pollution and better machinability. The present work investigates the tool wear during dry and wet turning of free-cutting steels (SAE 1212, SAE 12L14, and SAE 1215) by using uncoated hard metal inserts at three cutting speeds. Additionally, a EDS analysis was performed to determine the presence of Mn and S elements at the rake face of the cutting tool that can induce a higher adhesion of manganese sulfide (MnS). The results show that the SAE 12L14 steel has the best performance in terms of tool life at different cutting speeds. This difference is maximum at the lowest cutting speed, which gradually decreases with the increase of the cutting speed. The wear behavior is evaluated in the three steel alloys at each cutting speed and, consequently, the tool wear exhibits a slightly better performance in the dry machining condition for higher cutting speeds (180 and 240 m/min), independent of the steel alloy. Finally, EDS analysis confirms the presence of Mn and S elements at the rake face of the inserts machined in dry condition. Hence, MnS is expected to interpose between the machined surface and cutting tool surface to behave similar to tribofilm by reducing the wear on the cutting edge.