On-stream inspections are the most appropriate method for routine inspections during plant operation without undergoing production downtime. Ultrasonic inspection, one of the on-stream inspection methods, faces challenges when performed at high temperatures exceeding the recommended 52 °C. This study aims to determine the ultrasonic velocity and attenuation with known material grade, thickness, and temperatures by comparing theoretical calculation and experimentation, with temperatures ranging between 30 °C to 250 °C on low-carbon steel, covering most petrochemical equipment material and working conditions. The aim of the theoretical analysis was to obtain Young’s modulus, Poisson’s ratio, and longitudinal velocity at different temperatures. The experiments validated the theoretical results of ultrasonic change due to temperature increase. It was found that the difference between the experiments and theoretical calculation is 3% at maximum. The experimental data of velocity and decibel change from the temperature range provide a reference for the future when dealing with unknown materials information on site that requires a quick corrosion status determination.

Oat husk (OH; hull) is a by-product generated from oat processing and is rich in insoluble fibre and phenolic compounds. The aim of this work was to study the particle size distribution, antioxidant activity, and phenolic profile of micronized OH. For this purpose, the hull was first sterilized using superheated steam and was then ground using an impact classifier mill. The particle size distribution (PSD) of the ground husk was determined using the laser diffraction method and the parameters characterizing the PSD of the ground husk, and its antioxidant activity were calculated. In addition, UPLC-MS/MS analysis of phenolic acids was also performed. Micronization of the sterilized husk effectively decreased the size of the particles, and with the increasing speed of the rotor and classifier, the median size of the particles (d₅₀) decreased from 63.8 to 16.7 µm. The following phenolic acids were identified in OH: ferulic, caffeic, p-hydroxybenzoic, vanillic, syringic, and synapic acid. Ferulic acid constituted about 95% of total phenolic acids. The antioxidant activity of the obtained extracts increased as the particle size of the micronized husk decreased. The highest half maximal inhibitory concentration (EC₅₀ index) was found for chelating power, and the lowest was found in the case of radical scavenging activity against DPPH.

This study aimed to investigate the possibility of utilizing oat by-products for fiber preparation. Oat husk (OH) and oat bran (OB) were micronized and used to prepare a novel product rich in fiber and with enhanced antioxidant properties. The basic chemical composition and phenolic acid profile were determined in OH and OB. The antioxidant properties of OH and OB were also analyzed. The type and strength of interactions between the biologically active compounds from their mixtures were characterized by an isobolographic analysis. The analyses showed that the sum of phenolic acids was higher in OH than in OB. Ferulic acid was dominant in both OH and OB; however, its content in OH was over sixfold higher than that in OB. The results also suggested that both OH and OB can be used for preparing fiber with enhanced antioxidant properties. The optimal composition of the preparation, with 60–70% of OH and 30–40% of OB, allows for obtaining a product with 60–70% fiber and enhanced antioxidant activity due to bioactive substances and their synergistic effect. The resulting product can be a valuable additive to various food and dietary supplements.

Petrochemical plants use on-stream inspection often to detect and monitor the corrosion on the equipment and piping system. Compared to ultrasonic thickness gauging and pulse-echo A-scan, phased array corrosion mapping has better coverability and can scan a large area to detect general and localized corrosion. This paper’s objective is to obtain documentary evidence for the accuracy of corrosion detection from 30 °C to 250 °C on A36 low-carbon steel by carrying out simulation experiments every 10 °C step. A minimum of three sets of phased array corrosion mapping data in each temperature were collected to study and evaluate the detectability. The data evidence could enhance the confidence level of the plant’s end users in using phased array mapping in the future during inspections. The experiments were found to be insufficiently thorough despite addressing the initial concerns, leaving more area for discussion in further studies, such as expanding the investigation to thicker carbon steel, stainless steel, and wedge materials.