Jawad Kadhim Al Aridhee

Dr. Jawad Kadhim Al Aridhee

Al-Muthanna University, As Samāwah, Al Muthanná, Iraq
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 March 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
GŁGrzegorz Łysiak
Grzegorz Łysiak
RKRyszard Kulig
Ryszard Kulig
Jawad Kadhim Al AridheeJawad Kadhim Al Aridhee
Jawad Kadhim Al Aridhee
Anaerobic digestion (AD) is widely used for the sustainable treatment of biological wastes and the production of biogas. Its byproduct, digestate, is a valuable organic waste and needs appropriate management, which is one of the major concerns with a negative impact on the efficiency of biogas installations. One approach to extend the utilization of digestate as well as improve its handling and storage characteristics is compaction into pellets. This study aimed to evaluate the behavior of digestate during cyclic loading and unloading in a closed matrix. The findings presented here may provide insights into the mechanisms of pellet formation for optimizing the production of pellets and improving their sustainable management. The study can be considered novel as it applied cyclic loading, for the first time, in view of densification modeling and pelleting prediction. A Zwick universal machine was used in the experiments. The moisture content of digestate was found to be 10–22%. Samples were loaded with a constant amplitude of 20 kN for 10 cycles. The distribution of energy inputs, including the total energy, energy of permanent deformations, and energy lost to elastic ones, was thoroughly evaluated. A decrease in the total loading energy was observed in the first cycle, in cycles 2–10, and after all 10 applied cycles due to the rise in the moisture content of digestate. Similar relations were also found for the nonrecoverable energy part. In subsequent cycles of loading/unloading, the values of total energy and permanent deformation energy fell asymptotically. One of the most noteworthy findings of the study was that the absolute values of elastic deformation energy were consistent across all the cycles and moisture levels. However, it was noted that the percentage of energy dissipated to elastic deformation in all cycles significantly increased as the moisture content increased. Loading, which contributed to elastic deformations, was identified as the key factor causing an increase in cumulative energy inputs, and the majority of the energy expended was dissipated. Dissipated energy was the only component that permanently altered the total energy required for compaction. Another important finding, which resulted from the analysis of successive courses of loading and unloading curves, was that the shape of the areas enclosed between the loading/unloading curves was significantly influenced by the moisture content of the digestate.

11 December 2019 in Sustainability
Verified
Journal Article
Open access
PDF file
Jawad Kadhim Al AridheeJawad Kadhim Al Aridhee
Jawad Kadhim Al Aridhee
GŁGrzegorz Łysiak
Grzegorz Łysiak
RKRyszard Kulig
Ryszard Kulig
Monika WójcikMonika Wójcik
Monika Wójcik
MPMarian Panasiewicz
Marian Panasiewicz
The aim of the study was to examine the Peleg and Normand model to characterize the overall stress relaxation behavior of wheat kernel at varying load conditions. The relaxation experiments were made with the help of the universal testing machine, Zwick Z020, by subjecting the samples to compression at four distinct initial load levels, i.e., 20 N, 30 N, 40 N, and 50 N. The measurements were made for four wheat varieties (two soft and two hard-type endosperms) and seven levels of moisture content. Relaxation characteristics were approximated with the help of the Peleg and Normand equation. An interactive influence of the load level, moisture, and wheat hardness on the Peleg and Normand constants has been confirmed. For moist kernels, a higher amount of absorbed compression energy was released, since less energy was required to keep the deformation at a constant level. The constants differed depending on wheat hardness. Higher values of k1 revealed that the initial force decay was slower for hard varieties. This is more characteristic of elastic behavior. Similarly, higher values of k2 pointed to a larger amount of elastic (recoverable) energy at the end of the relaxation. The initial loading level had no or only a slight effect on the model coefficients (Y(t), k1, and k2). The parameters of the Peleg and Normand model decreased with an increase in the water content in the kernels.

1 June 2020 in Agricultural Engineering
Verified
Journal Article
Open access
PDF file
SGSławomir Gawłowski
Sławomir Gawłowski
RKRyszard Kulig
Ryszard Kulig
GŁGrzegorz Łysiak
Grzegorz Łysiak
Jawad Kadhim Al AridheeJawad Kadhim Al Aridhee
Jawad Kadhim Al Aridhee
ZAZdybel Adam
Zdybel Adam
PHPaweł Hyła
Paweł Hyła
The objective of the paper was to determine the impact of moisture and rotational speed of threshers on the process of crushing of lupine seeds. Raw material was led to four levels of moisture from 8 to 14% every 2%. The studies were carried out on the laboratory hammer mill with the use of variable speeds of mill hammers within 5500-7000 rot∙min−1. The studies that were carried out proved significant relations (p<0.05) between the analysed process variables and energy consumption and susceptibility of seeds to crushing. It was stated that along with the increase of the rotational speed, a reduction in the drop of the average dimension of particles of mill takes place. Along with the increase of moisture of lupine from 8 to 14% a unit energy of crushing increases on average by approx. 83%. It was proved that the susceptibility ratio of seeds to crushing increases along with the increase of raw material moisture. Such relations were determined for all investigated rotational speeds of hammers.

16 December 2020 in Journal of Texture Studies
Verified
Journal Article
Closed access
PDF file
GŁGrzegorz Łysiak
Grzegorz Łysiak
Jawad Kadhim Al AridheeJawad Kadhim Al Aridhee
Jawad Kadhim Al Aridhee
RKRyszard Kulig
Ryszard Kulig
RRRenata Rozylo
Renata Rozylo
Monika WójcikMonika Wójcik
Monika Wójcik

16 June 2026 in Materials
Verified
Journal Article
Open access
PDF file
GŁGrzegorz Łysiak
Grzegorz Łysiak
Jawad Kadhim Al AridheeJawad Kadhim Al Aridhee
Jawad Kadhim Al Aridhee
RKRyszard Kulig
Ryszard Kulig
PSPawel Sobczak
Pawel Sobczak
RRRenata Rozylo
Renata Rozylo
APArtur Przywara
Artur Przywara
This study aimed to characterize the stress relaxation of wheat kernels of different hardness and varying moisture contents using generalized Maxwell models with three, five, and seven elements. Single-kernel stress relaxation tests were conducted under controlled axial compression to obtain force decay data, which were fitted using non-linear regression to estimate model constants. Positive correlations between kernel moisture content and Maxwell constants were observed, indicating greater magnitude of force decay and higher relaxation rates at higher moisture levels, while the residual force decreased. Significant differences in viscoelastic parameters were also found between hard and soft wheat varieties.

1 December 2024 in Tikrit journal for agricultural sciences
Verified
Journal Article
Open access
PDF file
FKFlaieh Hammed Kassar
Flaieh Hammed Kassar
AAAhmed Merza Abood
Ahmed Merza Abood
Jawad Kadhim Al AridheeJawad Kadhim Al Aridhee
Jawad Kadhim Al Aridhee
A field experiment was conducted during Winter Season 2022- 2023. The aim of experimental to evaluate the effect of tractor engine speeds and gear position on the vibration levels during sowing operation. The first factor was engine speed of tractor (1000, 1500 and 2000 rpm) and the second factor was the third gear position at two level high and low speed. The measurements were taken at three separate locations (platform, seat and steering wheel) of tractor, in three direction (vertical, horizontal and lateral). The experimental laid out using randomized complete block design (RCBD) with three replications. The results of this study indicated that vibration level was increased as the engine speed of tractor increased at platform, seat and steering wheel in all directions. The change in the gear position setting has a significant effect on the vibration level. The lowest value of vibration acceleration (2.633m.s-2) was obtained at low speed. The maximum acceleration level (9.472m.s-2) was achieved at lateral direction in steering wheel location whereas, the minimum value (1.100m.s-2) was obtained at 1000 engine speed and low gear position in horizontal direction in seat location.