In this research, a convective/infrared (CV/IR) dryer was used to dry pumpkin slices. For optimization of the drying conditions, the influence of three levels of independent variables including air temperature (40, 55, and 70 °C), air velocity (0.5, 1, and 1.5 m/s), and IR power (250, 500, and 750 W) were assessed by response surface method (RSM) through a face-centered central composite design. Analysis of variance (non-fitting factor and R² value) was employed to determine the desirability of the model. Response surfaces and diagrams were also utilized to show the interactive influence of the independent variables with the response variables (drying time, energy consumption, shrinkage, total color variation, rehydration ratio, total phenol, antioxidant, and vitamin C contents). According to the results, optimal drying conditions involved a temperature of 70 °C, air velocity of 0.69 m/s, and IR power of 750 W. At the mentioned conditions, response variables of drying time, energy consumption, shrinkage, color, rehydration ratio, total phenol, antioxidant, and vitamin C contents were 72.53 min, 24.52 MJ/kg, 23%, 14.74, 4.97, 617.97 mg GA/100 g dw, 81.57%, and 4.02 mg/g dw, with a confidence level of 0.948, respectively.

Red raspberries, which contain a variety of nutrients and phytochemicals that are beneficial for human health, can be utilized as a raw material in the creation of several supplements. This research suggests micronized powder of raspberry pomace production. The molecular characteristics (FTIR), sugar, and biological potential (phenolic compounds and antioxidant activity) of micronized raspberry powders were investigated. FTIR spectroscopy results revealed spectral changes in the ranges with maxima at ~1720, 1635, and 1326, as well as intensity changes in practically the entire spectral range analyzed. The discrepancies clearly indicate that the micronization of the raspberry byproduct samples cleaved the intramolecular hydrogen bonds in the polysaccharides present in the samples, thus increasing the respective content of simple saccharides. In comparison to the control powders, more glucose and fructose were recovered from the micronized samples of the raspberry powders. The study’s micronized powders were found to contain nine different types of phenolic compounds, including rutin, elagic acid derivatives, cyanidin-3-sophoroside, cyanidin-3-(2-glucosylrutinoside), cyanidin-3-rutinoside, pelargonidin-3-rutinoside, and elagic acid derivatives. Significantly higher concentrations of ellagic acid and ellagic acid derivatives and rutin were found in the micronized samples than in the control sample. The antioxidant potential assessed by ABTS and FRAP significantly increased following the micronization procedure.

Anaerobic digestion (AD) is widely used for the sustainable treatment of biological wastes and the production of biogas. Its byproduct, digestate, is a valuable organic waste and needs appropriate management, which is one of the major concerns with a negative impact on the efficiency of biogas installations. One approach to extend the utilization of digestate as well as improve its handling and storage characteristics is compaction into pellets. This study aimed to evaluate the behavior of digestate during cyclic loading and unloading in a closed matrix. The findings presented here may provide insights into the mechanisms of pellet formation for optimizing the production of pellets and improving their sustainable management. The study can be considered novel as it applied cyclic loading, for the first time, in view of densification modeling and pelleting prediction. A Zwick universal machine was used in the experiments. The moisture content of digestate was found to be 10–22%. Samples were loaded with a constant amplitude of 20 kN for 10 cycles. The distribution of energy inputs, including the total energy, energy of permanent deformations, and energy lost to elastic ones, was thoroughly evaluated. A decrease in the total loading energy was observed in the first cycle, in cycles 2–10, and after all 10 applied cycles due to the rise in the moisture content of digestate. Similar relations were also found for the nonrecoverable energy part. In subsequent cycles of loading/unloading, the values of total energy and permanent deformation energy fell asymptotically. One of the most noteworthy findings of the study was that the absolute values of elastic deformation energy were consistent across all the cycles and moisture levels. However, it was noted that the percentage of energy dissipated to elastic deformation in all cycles significantly increased as the moisture content increased. Loading, which contributed to elastic deformations, was identified as the key factor causing an increase in cumulative energy inputs, and the majority of the energy expended was dissipated. Dissipated energy was the only component that permanently altered the total energy required for compaction. Another important finding, which resulted from the analysis of successive courses of loading and unloading curves, was that the shape of the areas enclosed between the loading/unloading curves was significantly influenced by the moisture content of the digestate.

In the present study, imperative parameters including centrifugal force, erosion, streamline, strain rate, and wall shear are evaluated in a cyclone separator. The flaw of the cyclone surface due to erosion is an acute problem in the industry. According to the great importance of the centrifugal force on the separation phenomenon, a comprehensive study is conducted. A computational fluid dynamics (CFD) simulation is realized by applying a Reynolds stress turbulence model (RSM), and particle–air interactions were modeled using a discrete phase model (DPM). The result shows a good agreement between the experimental data and CFD simulation on the tangential velocity and pressure drop. The maximum deviation of the validation process is 6.8%. It is found that the centrifugal force within the cyclone is increased with an enhancement in the inlet velocity. The separation efficiency indicates an increase–decrease treatment in various inlet velocities with inlet velocity up to 16 m⋅s⁻¹ but decreases slightly at a velocity of 20 m⋅s⁻¹. The pressure increases proportionally with inlet velocity. The best performance with the highest separation efficiency (99%) and pressure drop (416 Pa) obtains at the inlet velocity of 16 m⋅s⁻¹ and mass flow rate of 0.01 kg⋅s⁻¹. In addition, the maximum erosion rate was created in the entrance and conical part of the cyclone.