To investigate the effect of twin swirl and bulk swirl on the performance and stability of a transonic axial compressor, a blade swirl generator was designed and simulated with a transonic single rotor using steady and unsteady numerical calculation methods. The bulk swirl intensity was adjusted by replacing the blades with different camber angles. The twin swirl intensity was decreased by reducing the blade number. The counter-rotating bulk swirl generated a significant drop in both the efficiency and stall margin, and resulted in an increase in the choked mass flow, and total pressure ratio. The co-rotating bulk swirl generated a decrease in the mass flow, total pressure ratio and stable operating range. The counter-rotating bulk swirl resulted in suction surface boundary layer separation beyond 50% of the span-wise height as well as more serious tip leakage blockage. The twin swirl resulted in a decrease in the total pressure ratio, maximum efficiency and stable operating range. The steady and unsteady numerical calculation results were consistent, though some differences were observed in the values. For the steady calculation, the maximum efficiency and choked mass flow decreased by 0.88% and 1.74%, respectively, and the mass flow at the stable boundary increased by 3.92% as compared to the uniform inlet flow at twin swirl intensity of 24°. During the unsteady calculation, the mass flow exhibited an increase of only 2.2% at the stable boundary. Under twin swirl and co-rotating bulk swirl and uniform inlet flow, the leading edge spillage of the tip leakage flow resulted in compressor instability. The counter-rotating bulk swirl changed the mechanism of instability. The characterisation of the swirl distortion presented a difference between the steady and unsteady calculations near the stable boundary. The unsteady calculation exhibited a lower mass flow at the stable boundary point and a higher total pressure ratio.
18 August 2021 in International Journal of Aerospace Engineering
In order to detect the aerodynamic instability of a multistage axial compressor more accurately and earlier, the harmonic Fourier mean amplitude analysis method and heterotopic variance analysis method are developed. The dynamic instability prediction performance of the two methods is studied on a low-speed and a high-speed two-stage axial compressor. The harmonic Fourier mean amplitude analysis method is suitable for predicting the aerodynamic instability of a multistage axial compressor in the form of a rotating stall. Compared with the traditional harmonic Fourier analysis methods, the harmonic Fourier mean amplitude analysis method can capture the detail of the pressure signal more accurately and it can effectively prevent instability misjudgment. The heterotopic variance analysis method is developed based on the conventional variance analysis method, and it can be used to distinguish whether the compressor is in the rotating stall or the surge state. The heterotopic variance analysis method can predict the aerodynamic instability ahead of the harmonic Fourier mean amplitude analysis method, and fewer circumferential measuring points were employed. The layout of the measuring points also influences the detection of the aerodynamic instability of the compressor. The aerodynamic instability of the high-speed axial compressor can be predicted earlier by employing measuring points at the compressor outlet.
17 December 2018 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
To investigate the effect of high-temperature steam ingestion on the aerodynamic stability of a transonic axial compressor, a NASA Rotor 37 was numerically simulated. The effects of the high-temperature steam mass fraction, the temperature rise rate, the maximum temperature, and the distribution of steam at the inlet boundary on the aerodynamic stability of a transonic axial rotor were investigated, using the steady-state and quasi-steady methods. From the simulation results, it was found that high-temperature steam ingestion has an adverse effect on the transonic rotor. The greater the steam mass fraction and the maximum temperature, the greater the impact of the steam ingestion on the stability boundary. The temperature rise rate has little effect on the performance and stability. The distribution of steam at the inlet boundary has a significant impact on the performance and stability. In addition, with the ingestion of high-temperature steam, the average density of the gas at the rotor inlet is affected, and the passage shock position moves forward at the same time, which leads to the occurrence of the stall in advance.
The aim of this article mainly lies in two aspects. The first is to investigate the effect of inlet swirl distortion on the performance and stability of a low-speed compressor experimentally. The second is to quantify swirl pattern revolution through the compressor and find out background causes of the change in compressor performance. Swirl distortion makes the leading-edge incidence opposite between tip and hub regions, compared to that of clean flow. And the compressor performance change is ultimately determined by these two aspects. Results indicate that negative bulk swirl improves pressure rise, and the effect is on the contrary to the positive bulk swirl. Under the condition of paired swirl, pressure rise also presents a reduction. All these three types of swirl have little effect on the stall boundary. Although swirl distortion shows clear recovery at rotor exit, downstream components still work at off-design conditions due to the induced nonuniformity in axial velocity and total pressure.
15 April 2019 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
This paper presents a mixed-fidelity model to investigate the effect of complex inlet distortion on aero gas turbine engines. The approach is developed by integrating a three-dimensional body force model of multistage compressors and a classical two-dimensional parallel engine model. The internal flow field of a high bypass ratio turbofan engine under different forms of total pressure distortion is simulated by the model. The simulations are discussed in depth to reveal the features of the distorted flow field in the compression components under the whole engine environment. The relationship between the overall performance of the engine and the intensity of inlet total pressure distortion is investigated quantitatively. It is evident that the mixed-fidelity model has the capability to quantitatively evaluate the effect of complex inlet distortion on the performance and the internal flow field of engines with low computational costs.
21 January 2020 in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
In order to improve the performance of high-loaded compressor stator with large camber turning angle, a stator cascade blade with tubercle leading edge was designed based on the wavy leading edge of humpback’s flipper, and computational fluid dynamics simulation was carried out. The results show that the tubercle leading edge can effectively improve the aerodynamic performance of the stator cascade at high attack angles, and the total pressure loss coefficient can be reduced by 26.46%. The main reason why the tubercle structure improves the performance is that it makes the radial displacement of airflow appear as a butterfly-like structure at the leading edge of the blade, which restrains the occurrence and development of airflow separation. By comparing the performance of the blades with full-span and part-span tubercle leading edges, it is considered that the tubercle leading edge of 80% blade height in the mainstream region can improve the aerodynamic performance of cascade better, while the one of 50% blade height has the worst effect.