Atomic layer deposition (ALD) is gaining attention as a catalyst preparation method able to produce metal (oxide, sulphide, etc.) nanoparticles of uniform size down to single atoms. This work reports our initial experiments to support nickel on mesoporous zirconia. Nickel (2,2,6,6-tetramethyl-3,5-heptanedionate)2 [Ni(thd)2] was reacted in a fixed-bed ALD reactor with zirconia, characterised with BET surface area of 72 m2/g and mean pore size of 14 nm. According to X-ray fluorescence measurements, the average nickel loading on the top part of the support bed was on the order of 1 wt%, corresponding to circa one nickel atom per square nanometre. Cross-sectional scanning electron microscopy combined with energy-dispersive spectroscopy confirmed that in the top part of the fixed support bed, nickel was distributed throughout the zirconia particles. X-ray photoelectron spectroscopy indicated the nickel oxidation state to be two. Organic thd ligands remained complete on the surface after the Ni(thd)2 reaction with zirconia, as followed with diffuse reflectance infrared Fourier transform spectroscopy. The ligands could be fully removed by oxidation at 400 °C. These initial results indicate that nickel catalysts on zirconia can likely be made by ALD. Before catalytic testing, in addition to increasing the nickel loading by repeated ALD cycles, optimization of the process parameters is required to ensure uniform distribution of nickel throughout the support bed and within the zirconia particles.
The hydrodeoxygenation (HDO) of levulinic acid (LA) aldol condensation product dimers was studied between 250 and 300 °C and 50 bar H2 in a batch reactor with Ru catalyst supported on mesoporous zirconia. During the reaction, the unsaturated dimers, which contained ketone groups and double bonds, were hydrogenated to saturated dimers. A greater degree of deoxygenation was achieved at higher temperatures, and oxygen was removed as water and CO2. Oxygen removal was evidenced by elemental analysis and infrared spectroscopy, in which the C=O peak decreased with increasing temperature. A drawback of high reaction temperature (300 °C) was a minor degree of oligomerization. The formation of aromatics was also observed at the higher temperatures. Aside from the saturated dimers, volatile products were obtained at all temperatures, including ketones, acids, and esters. This study demonstrates for the first time the potential of LA dimers as a sustainable route from lignocellulosic biomass to biofuels and biocomponents.
Pyrolysis and liquefaction biocrudes obtained from lignocellulose are rich in phenolic compounds that can be converted to renewable aromatics. In this study, Pt catalysts on reducible metal oxide supports (Nb2O5, TiO2), along with irreducible ZrO2 as a reference, were investigated in the liquid‐phase hydrodeoxygenation (HDO) of 4‐propylphenol (350 °C, 20 bar H2, organic solvent). The most active catalyst was Pt/Nb2O5, which led to the molar propylbenzene selectivity of 77 %, and a yield of 75 % (98 % conversion). Reducible metal oxide supports provided an increased activity and selectivity to the aromatic product compared to ZrO2, and the obtained results are among the best reported in liquid‐phase. The reusability of the spent catalysts was also studied. The spent Pt/Nb2O5 catalyst provided the lowest conversion, while the product distribution of the spent Pt/ZrO2 catalyst changed towards oxygenates. The results highlight the potential of pyrolysis or liquefaction biocrudes as a source of aromatic chemicals.
The possibility to valorize levulinic acid (LA) dimers to lignocellulose-based biofuels via hydrodeoxygenation (HDO) was assessed using γ-nonalactone (GNL) as a model compound. Catalytic HDO experiments were performed in a batch reactor at 280 °C and at an average pressure of 57.5 bar H2. Noble metal (Ru, Rh, Pd, and Pt) catalysts supported on ZrO2. All the catalysts were active in removing oxygen from the reactant. However, the most selective catalyst for hydrocarbons (24%) was ruthenium. Unlike the other tested catalysts, Ru also provided branched hydrocarbons. In view of Ru’s comparatively high selectivity to hydrocarbons, it was tested at various reaction temperatures (220–280 °C) for 300 min. The experiments at lower temperatures resulted in less hydrocarbons and more intermediate products, such as alcohols. In total, nearly 70 products were identified, and some of the reactions that likely occurred in the HDO experiments were discussed. The production of hydrocarbons from GNL highlights the potential of LA dimers as a route to lignocellulose-based biofuels.
The alkylphenols found in liquefied lignocellulose could become a source of bio‐based aromatic hydrocarbons for fuel components. In the hydrodeoxygenation (HDO) of alkylphenols, hydroxyl groups must be removed while avoiding the hydrogenation of the aromatic ring. Here, the HDO of propylphenols is studied using a Pt/Nb2O5 catalyst and n‐tetradecane solvent. HDO experiments are performed using different reaction conditions of batch residence time (0–161 min gcat greactant−1), pressure (20–30 bar H2), and temperature (300–375 °C). HDO is studied with ortho‐, meta‐, and para‐propylphenol. The influence of vapor–liquid equilibrium and chemical equilibrium are assessed using thermodynamic calculations. Almost full deoxygenation is attained in the experiments; the main products are propylbenzene and propylcyclohexane. The study finds that, of the isomers, 4‐propylphenol is the most favorable for forming propylbenzene (77% maximum selectivity), whereas 2‐propylphenol is the least favorable (55% maximum selectivity). Additionally, the reactivity of propylbenzene in the test conditions is detrimental to its selectivity after 5 min gcat greactant−1. Finally, the temperature at which the process favors propylbenzene is found to shift as a function of pressure; at 20 bar, propylbenzene is favored at 350 °C and at 30 bar, it is favored at 375 °C.