Arrays of microneedles (MNAs) are integrated in an out-of-plane fashion with a base plate and can serve as patches for the release of drugs and vaccines. We used soft-lithography and micromolding to manufacture ceramic nanoporous (np)MNAs. Failure modes of ceramic npMNAs are as yet poorly understood and the question remained: is our npMNA platform technology ready for microneedle (MN) assembly into patches? We investigated npMNAs by microindentation, yielding average crack fracture forces above the required insertion force for a single MN to penetrate human skin. We further developed a thumb pressure-actuated applicator-assisted npMNA insertion method, which enables anchoring of MNs in the skin by an adhesive in one handling step. Using a set of simple artificial skin models, we found a puncture efficiency of this insertion method a factor three times higher than by applying thumb pressure on the npMNA base plate directly. In addition, this new method facilitated zero MN-breakage due to a well-defined force distribution exerted onto the MNs and the closely surrounding area prior to bringing the adhesive into contact with the skin. Owing to the fact that such parameter space exists, we can conclude that npMNAs by soft lithography are a platform technology for MN assembly into a patch.
The vasculature plays a central role as the highway of the body, through which nutrients and oxygen as well as biochemical factors and signals are distributed by blood flow. Therefore, understanding the flow and distribution of particles inside the vasculature is valuable both in healthy and disease-associated networks. By creating models that mimic the microvasculature fundamental knowledge can be obtained about these parameters. However, microfabrication of such models remains a challenging goal. In this paper we demonstrate a promising 3D sugar printing method that is capable of recapitulating the vascular network geometry with a vessel diameter range of 1 mm down to 150 µm. For this work a dedicated 3D printing setup was built that is capable of accurately printing the sugar glass material with control over fibre diameter and shape. By casting of printed sugar glass networks in PDMS and dissolving the sugar glass, perfusable networks with circular cross-sectional channels are obtained. Using particle image velocimetry, analysis of the flow behaviour was conducted showing a Poisseuille flow profile inside the network and validating the quality of the printing process.
2 February 2021 in IEEE Transactions on Automation Science and Engineering
Since the introduction of adaptive systems for corrective measures, static and dynamic disturbances have been reduced through the manipulation of surface shape in a well-controlled manner. One important application where adaptive systems are highly needed is in the future photo-lithography machines, particularly the wafer table where disturbances affect overlay and focus performance. To reduce overlay and focus errors, a dense array of actuators must be integrated into the wafer table to apply both in- and out-of-plane corrective deformations to the wafer surface. To realize a certain wafer shape, influence functions are linearly superimposed. Accurate models of the influence functions result in an accurate prediction of the final wafer shape. To reduce calibration errors, the influence function of every actuator needs to be determined. Here, we propose a technique to rapidly measure the influence function: the influence function measurement (IFM) technique. Using the actuate-sense property of piezoelectric materials, the influence function is determined by activating one piezo-actuator and measuring the charge induced on the neighboring piezo-actuators. The measured charges are compared to the results of finite element simulations and the absolute difference of 0.3 % is reported for the inter-actuator charge coupling parameters. This clearly indicates the potential of the proposed technique. Note to Practitioners —A critical step during the integrated-circuit lithographic fabrication process is the exposure. A particular practical challenge in this step is to correct for the mismatch between the optical image plane and the wafer surface, caused by wafer deformations. The mismatch negatively impacts the overlay and focus performance. To reduce the mismatch, actuators can be embedded into the wafer table to counteract wafer deformations, where the overall wafer surface shape is a superposition of each actuator’s influence function. As part of the calibration for the embedded actuators, their influence functions are measured and stored. However, errors arise when influence functions are not measured for every actuator. Additionally, for different wafers, the influence functions vary hence the calibration should be done per wafer. This calibration process takes time and should not influence throughput. Our paper presents a viable approach that reduces the calibration time of active wafer tables, which is also relevant for other adaptive systems such as deformable mirrors. Since the technique requires the actuators to be mechanically coupled, it is limited to continuous surfaces. The proposed technique is numerically tested and experimentally verified to demonstrate performance.