Andrea Bianco

Dr. Andrea Bianco


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2020 in Energies
Verified
Journal Article
Open access
PDF file
Federico MilloFederico Millo
Federico Millo
APAndrea Piano
Andrea Piano
BPBenedetta Peiretti Paradisi
Benedetta Peiretti Paradisi
MMMario Rocco Marzano
Mario Rocco Marzano
ABAndrea Bianco
Andrea Bianco
FPFrancesco C. Pesce
Francesco C. Pesce
In this paper, an integrated and automated methodology for the coupling between 1D- and 3D-CFD simulation codes is presented, which has been developed to support the design and calibration of new diesel engines. The aim of the proposed methodology is to couple 1D engine models, which may be available in the early stage engine development phases, with 3D predictive combustion simulations, in order to obtain reliable estimates of engine performance and emissions for newly designed automotive diesel engines. The coupling procedure features simulations performed in 1D-CFD by means of GT-SUITE and in 3D-CFD by means of Converge, executed within a specifically designed calculation methodology. An assessment of the coupling procedure has been performed by comparing its results with experimental data acquired on an automotive diesel engine, considering different working points, including both part load and full load conditions. Different multiple injection schedules have been evaluated for part-load operation, including pre and post injections. The proposed methodology, featuring detailed 3D chemistry modeling, was proven to be capable assessing pollutant formation properly, specifically to estimate NOx concentrations. Soot formation trends were also well-matched for most of the explored working points. The proposed procedure can therefore be considered as a suitable methodology to support the design and calibration of new diesel engines, due to its ability to provide reliable engine performance and emissions estimations from the early stage of a new engine development.

21 May 2022 in Energies
Verified
Journal Article
Open access
PDF file
Federico MilloFederico Millo
Federico Millo
APAndrea Piano
Andrea Piano
SRSalvatore Roggio
Salvatore Roggio
FPFrancesco C. Pesce
Francesco C. Pesce
AVAlberto Vassallo
Alberto Vassallo
ABAndrea Bianco
Andrea Bianco
The optimization of the piston bowl design has been shown to have a great potential for air–fuel mixing improvement, leading to significant fuel consumption and pollutant emissions reductions for diesel engines. With this aim, a conventional re-entrant bowl for a 1.6 L light-duty diesel engine was compared with two innovative piston designs: a stepped-lip bowl and a radial-bumps bowl. The potential benefits of these innovative bowls were assessed through 3D-CFD simulations, featuring a calibrated spray model and detailed chemistry. To analyse the impact of these innovative designs, two different engine operating conditions were scrutinized, corresponding to the rated power and a partial load, respectively. Under the rated power engine operating condition, a start of injection sensitivity was then carried out to assess the optimal spray–wall interaction. Results highlighted that, thanks to optimal injection phasing, faster mixing-controlled combustion could be reached with both the innovative designs. Moreover, the requirements in terms of swirl were also investigated, and a higher swirl ratio was found to be necessary to improve the mixing process, especially for the radial-bumps design. Finally, at part-load operating conditions, different exhaust gas recirculation (EGR) rates were analysed for two injection pressure levels. The stepped-lip and radial-bumps bowls highlighted reduced indicated specific fuel consumption (ISFC) and soot emissions values over different rail pressure levels, guaranteeing NOx control thanks to the higher EGR tolerance compared with the re-entrant bowl. The results suggested the great potential of the investigated innovative bowls for improving efficiency and reducing emissions, thus paving the way for further possible optimization through the combination of these designs.

16 December 2019 in Preprints.org
Verified
Preprint
Open access
PDF file
Federico MilloFederico Millo
Federico Millo
APAndrea Piano
Andrea Piano
BPBenedetta Peiretti Paradisi
Benedetta Peiretti Paradisi
MMMario Rocco Marzano
Mario Rocco Marzano
ABAndrea Bianco
Andrea Bianco
FPFrancesco C. Pesce
Francesco C. Pesce
In this paper an integrated methodology for the coupling between 1D- and 3D-CFD simulation codes is presented, which has been developed to support the design and calibration of new diesel engines. The aim of the proposed methodology is to couple 1D engine models, which may be available in the early-stage engine development phases, with 3D predictive combustion simulations, in order to obtain reliable estimates of engine performance and emissions for newly designed automotive diesel engines. The coupling procedure features simulations performed in 1D-CFD by means of GT-SUITE and in 3D-CFD by means of Converge, executed within a specifically designed calculation methodology. An assessment of the coupling procedure has been performed by comparing its results with experimental data acquired on an automotive Diesel engine, considering different working points including both part load and full load conditions. Different multiple injection schedules have been evaluated for part-load operation, including pre and post injections. The proposed methodology, featuring detailed 3D chemistry modeling, was proven to be capable to properly assess pollutant formation, specifically to estimate NOx concentrations. Soot formation trend was also well-matched for most of the explored working points. The proposed procedure can therefore be considered as a suitable methodology to support the design and calibration of new Diesel engines, thanks to its ability to provide reliable engine performance and emissions estimations from the early-stage of a new engine development.