Wei Wei

Dr. Wei Wei

Dalian Jiaotong University, 794 Huanghe Road, Shahekou District, Dalian, Liaoning province 116028, PR China
+1
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2021 in Engineering Fracture Mechanics
Verified
Journal Article
Closed access
Wei WeiWei Wei
Wei Wei
LDLiang Du
Liang Du
GYGuang Yang
Guang Yang
YZYuntong Zhang
Yuntong Zhang
YSYang Sun
Yang Sun
XYXinhua Yang
Xinhua Yang

7 March 2025 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
MMMinze Ma
Minze Ma
Wei WeiWei Wei
Wei Wei
HZHe Zhang
He Zhang
ZYZe Yao
Ze Yao
YSYang Sun
Yang Sun
FWFufa Wu
Fufa Wu

29 January 2021 in Metals
Verified
Journal Article
Open access
PDF file
Wei WeiWei Wei
Wei Wei
CLCheng Li
Cheng Li
YSYibo Sun
Yibo Sun
HXHongji Xu
Hongji Xu
XYXinhua Yang
Xinhua Yang
In this study, we investigated the fatigue behavior of Q460 welded joints using tensile fatigue tests. Furthermore, real-time temperature profiles of the examined specimens were recorded by infrared thermography. Based on the obtained thermographic data, we calculated the entropy production rate of the specimens under different stress amplitudes. Hypothetically, the entropy production during high-cycle fatigue (HCF) could be divided into two parts. The first is induced by inelastic behavior that corresponds to damage accumulation, and the second originates from anelasticity associated with recoverable non-damaging microstructural motions. The turning point of entropy production under different stress levels represents an index for fatigue limit estimation. Then, considering the average damage threshold that exists during HCF, the entropy production related to damage accumulation (cumulative damage entropy) is obtained by testing three specimens under the same stress amplitude above the fatigue limit. Finally, a rapid three-parameter S-N curve with a survival probability rate of 50% is obtained. Then, combined with the maximum likelihood method, the 5% and 95% survival probability rate S-N curves are established. Most of experimental data are distributed in the area between S-N curves that correspond to 5% and 95% survival probability rate, indicating good accordance with the test data.

11 September 2023 in Engineering Fracture Mechanics
Verified
Journal Article
Closed access
Wei WeiWei Wei
Wei Wei
LHLei He
Lei He
MCMinghua Chen
Minghua Chen
XCXueting Chen
Xueting Chen
RLRuiyang Liang
Ruiyang Liang
XYXinhua Yang
Xinhua Yang

24 September 2025 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
JLJianhui Li
Jianhui Li
Wei WeiWei Wei
Wei Wei
HZHe Zhang
He Zhang
ZYZe Yao
Ze Yao
YSYang Sun
Yang Sun
FWFufa Wu
Fufa Wu

13 September 2024 in Journal of Laser Applications
Verified
Journal Article
Closed access
PDF file
XCXueting Chen
Xueting Chen
YLYu Li
Yu Li
Wei WeiWei Wei
Wei Wei
GYGuili Yin
Guili Yin
LYLin Yang
Lin Yang
HSHai Su
Hai Su
In response to the problem of low hardness and poor wear resistance of TC4 coatings prepared by laser additive manufacturing, three titanium alloy coatings with different Si contents were prepared on a TC4 substrate by direct laser deposition (DLD) technology. The evolution of the microstructure and wear mechanism of the coatings were studied. The addition of the Si element facilitated the formation of Ti5Si3 hard phase, which exhibited a uniform mesh form. The strengthening effect of the hard phase in the prepared coating increased with its proportion, demonstrating a positive correlation with the incremental addition of an Si element. However, the excessive addition of the Si element resulted in the surface cracking of the coating. The optimal DLD Ti-Al-Si coating was obtained when the Si content was 10 wt. %, with an average microhardness of 801 ± 24 HV0.2, 2.5 times greater than that of the TC4 substrate. The average friction coefficient of the Ti-Al-Si coating was 0.39, and the wear rate was 1.9%. The hard phase was uniformly distributed in a mesh form, which not only refined the wear debris and suppressed the shear force of the wear debris during wear but also slowed down the continuous wear of debris on the worn surface. The results of this study could provide a reference for preparing high-hardness and wear-resistant titanium alloy coatings by DLD.