Xueting Chen

Dr. Xueting Chen

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2019 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
YZYue Zhou
Yue Zhou
SCSuiyuan Chen
Suiyuan Chen
XCXueting Chen
Xueting Chen
TCTong Cui
Tong Cui
JLJing Liang
Jing Liang
CLChangsheng Liu
Changsheng Liu

1 May 2020 in Optics & Laser Technology
Verified
Journal Article
Closed access
YZYue Zhou
Yue Zhou
SCSuiyuan Chen
Suiyuan Chen
XCXueting Chen
Xueting Chen
JLJing Liang
Jing Liang
CLChangsheng Liu
Changsheng Liu
MWMei Wang
Mei Wang

25 June 2019 in Powder Metallurgy
Verified
Journal Article
Closed access
XCXueting Chen
Xueting Chen
SCSuiyuan Chen
Suiyuan Chen
JLJing Liang
Jing Liang
TCTong Cui
Tong Cui
Changsheng LiuChangsheng Liu
Changsheng Liu
WMWang Mei
Wang Mei
A novel 15Cr13MoY alloy steel powder used for direct laser deposition was produced using the vacuum induction gas atomisation (VIGA) method. The characteristics and laser printability of the 15Cr13MoY alloy steel powder were studied. The flowability of the spherical powder was 18.98 s/50 g−1, and apparent density was 4.75 g cm−3. The fabricated 15Cr13MoY alloy steel samples composed of ferrite and bainite were prepared by DLD. The phases primarily consisted of a Fe–Cr–Mn solid solution M7C3, M23C6 and Y2O3. At the optimum laser power of 2200W, the average microhardness of 15Cr13MoY alloy steel sample was 350 HV, the tensile strength was 897 MPa, the yield strength was 704 MPa, the average elongation was 14.5%, and the product of strength and plasticity was 13.0 GPa%. The 15Cr13MoY alloy steel powder produced usingthe VIGA method had good powder characteristics and printability for fabricating the components produced by DLD.

20 June 2023 in Metals
Verified
Journal Article
Open access
PDF file
ZLZhanqi Liu
Zhanqi Liu
HWHaijiang Wang
Haijiang Wang
XCXueting Chen
Xueting Chen
WWWei Wei
Wei Wei
This work attempts to develop a theoretical model in combination with the representative volume element (RVE) theory for realizing rapid fatigue limit prediction. Within the thermodynamic framework, it is believed that two components, namely anelastic and microplastic behaviors, which correspond to recoverable and non-recoverable microstructural motions, contribute to temperature variation during high-cycle fatigue. Based on this, the constitutive equation of the response relationship between the temperature rise evolution and the stress amplitude of metallic materials can be deduced in combination with the heat balance equation. Meanwhile, a determination approach for the thermographic experimental data for accurate fatigue limit estimation is developed by combining it with a statistical method. Finally, the experimental data of metallic specimens and welded joints were utilized to validate the proposed model, and the results demonstrated great agreement between experimental and predicted data.

13 September 2024 in Journal of Laser Applications
Verified
Journal Article
Closed access
PDF file
XCXueting Chen
Xueting Chen
YLYu Li
Yu Li
Wei WeiWei Wei
Wei Wei
GYGuili Yin
Guili Yin
LYLin Yang
Lin Yang
HSHai Su
Hai Su
In response to the problem of low hardness and poor wear resistance of TC4 coatings prepared by laser additive manufacturing, three titanium alloy coatings with different Si contents were prepared on a TC4 substrate by direct laser deposition (DLD) technology. The evolution of the microstructure and wear mechanism of the coatings were studied. The addition of the Si element facilitated the formation of Ti5Si3 hard phase, which exhibited a uniform mesh form. The strengthening effect of the hard phase in the prepared coating increased with its proportion, demonstrating a positive correlation with the incremental addition of an Si element. However, the excessive addition of the Si element resulted in the surface cracking of the coating. The optimal DLD Ti-Al-Si coating was obtained when the Si content was 10 wt. %, with an average microhardness of 801 ± 24 HV0.2, 2.5 times greater than that of the TC4 substrate. The average friction coefficient of the Ti-Al-Si coating was 0.39, and the wear rate was 1.9%. The hard phase was uniformly distributed in a mesh form, which not only refined the wear debris and suppressed the shear force of the wear debris during wear but also slowed down the continuous wear of debris on the worn surface. The results of this study could provide a reference for preparing high-hardness and wear-resistant titanium alloy coatings by DLD.

1 September 2024 in Materials Research Express
Verified
Journal Article
Open access
XCXueting Chen
Xueting Chen
CZChang Zhao
Chang Zhao
XZXiaoou Zhu
Xiaoou Zhu
GYGuili Yin
Guili Yin
YXYun Xu
Yun Xu
The 70Cr8Ni2Y coatings were prepared by direct laser deposition (DLD) with different scanning speeds. The microstructure evolution and the relationship between microstructure and properties of the coatings were studied. The results demonstrated that the microstructure of DLD 70Cr8Ni2Y coatings was martensite, and the phases were α′ (Fe-Cr) and γ-Fe (Fe-Ni). With the increased of scanning speed, the martensite size decreased from 5.42 ± 0.04 μm to 4.42 ± 0.01 μm and 3.20 ± 0.02 μm. When the scanning speed was 20 mm s−1, the fabricated coating displayed the highest average microhardness (883 ± 37 HV) and the lowest mass wear rate (0.061 mg mm−1) without pores. The combined strengthening effect of fine grain strengthening and solid solution strengthening, as well as good formability, were the fundamental reasons for the high hardness and wear resistance of the coating. The results of this study can provide an experimental basis for the DLD alloy coatings with high hardness and wear resistance.