In this paper is presented the simulation and analysis of a Fuzzy Energy Management for Hybrid Fuel cell/Battery Systems used for More Electric Aircraft. The fuel cell hybrid system contains of fuel cell, lithium-ion batteries along with associated dc to dc boost converters. In this configuration the battery has a dc to dc converter, because it is an active in the system. The energy management scheme includes the rule based fuzzy logic strategy. This scheme has a faster response to load change and is more robust to measurement imprecisions. Simulation will be provided using Matlab/Simulink based models. Simulation results are given to show the overall system performance.
This chapter deals with some intensive methods regarding aircraft gas-turbine-engine performance enhancement, which are suitable alternatives for the most common temporarily thrust increasing method—the afterburning. Coolant injection method, into the compressor or into the combustor, realizes the desired thrust increase for a short period, when the flight conditions or other aircraft necessities require this. Both methods were studied from aircraft engine’s point of view, considering it as controlled object. New engine’s mathematical model was built up, following the thermo- and gas-dynamics changes and some quality studies were performed, based on engine’s time behavior simulations; some control options and schemes were also studied. Quantitative studies were based on the model of an existing turbo-engine; mathematical model’s coefficients are both experimentally determined (in the Aerospace Engineering Division labs) as well as estimated based on graphic-analytic methods. This approach and the presented methods could be applied to any other turbo-jet engine and used even in the stage of pre-design of a new engine, to estimate its stability and quality.
The paper proposes a novel automatic control system for the attitude of the mini-satellites equipped with an actuator having N = 2 DGMSCMGs (Double Gimbal Magnetically Suspended Control Moment Gyros) in parallel and orthogonal configuration, as well as a DGMSCMG-type sensor for the measurement of the satellite absolute angular rate. The proportional-derivative controller, designed based on the Lyapunov-functions theory, elaborates the control law according to which the angular rates applied to the servo systems for the actuation of the DGMSCMGs gyroscopic gimbals are computed. The gimbal’s angular rates create gyroscopic couples acting on the satellite in order to control its attitude with respect to the local orbital frame. The new proposed control architecture was software implemented and validated, and the analysis of the obtained results proved the cancellation of the convergence errors and excellent angular rate precision.
The paper presents a way to obtain an intelligent miniaturized three-axial accelerometric sensor, based on the on-line estimation and compensation of the sensor errors generated by the environmental temperature variation. Taking into account that this error’s value is a strongly nonlinear complex function of the values of environmental temperature and of the acceleration exciting the sensor, its correction may not be done off-line and it requires the presence of an additional temperature sensor. The proposed identification methodology for the error model is based on the least square method which process off-line the numerical values obtained from the accelerometer experimental testing for different values of acceleration applied to its axes of sensitivity and for different values of operating temperature. A final analysis of the error level after the compensation highlights the best variant for the matrix in the error model. In the sections of the paper are shown the results of the experimental testing of the accelerometer on all the three sensitivity axes, the identification of the error models on each axis by using the least square method, and the validation of the obtained models with experimental values. For all of the three detection channels was obtained a reduction by almost two orders of magnitude of the acceleration absolute maximum error due to environmental temperature variation.
This study addresses an under-represented topic in turbojets’ design—the characterizing of this type of engine as an entity subject to automatic control. This study’s subject is a medium-size turbojet, improved with a water injection system for thrust augmentation, and evaluated as a controlled object. The method of coolant injection in the compressor and/or in the combustion chamber of the aviation engine has been intensively studied and applied for the temporary increase in thrust. After a period of abandonment, the method seems to be returning in a version that also produces a reduction in pollutant emissions. Starting from determining turbojet performances on the test rig and establishing the equations that define the turbojet as a system, the mathematical model for both versions (basic and with a water injection) was issued. In order to correlate the basic engine operation with the water injection, a version of control architecture was designed, containing two controllers (for engine’s speed and for the injected water flow rate). An embedded control system was described by its mathematical model; based on its equations, its block diagram with transfer functions was issued. The system’s quality was evaluated by performing studies that concern the turbojet’s main parameters (speed and combustor temperature) and time behavior (system response at step input), which led to some results and conclusions regarding how the water injection changed the properties of the engine as a controlled object: the engine has become slower with bigger static errors for the studied parameters (affecting the stabilization at their values imposed by the new operating regime). The proposed method, based on the characterization of the engine as a controlled object (with and without coolant injection), can be very useful as a method of predicting the behavior of any turbojet when the addition of coolant injection system is desired; obviously, the appropriate modeling of both the turbojet and the injection system is necessary.