Soil steam disinfection (SSD) technology is an effective means of eliminating soil borne diseases. Among the soil cultivation conditions of facility agriculture in the Yangtze River Delta region of China, the clay soil particles (SPs) are fine, the soil pores are small, and the texture is relatively viscous. When injection disinfection technology is applied in the clay soil, the diffusion of steam is hindered and the heating efficiency is substantially affected. To increase the heating efficiency of SSD, we first discretized the continuum model of Philip and De Vries into circular particle porous media of different sizes and random distribution. Then with Computational Fluid Dynamics (CFD) numerical simulation technology, a single-injection steam disinfection model for different SP size conditions was constructed. Furthermore, the diffusion pattern of the macro-porous vapor flow and matrix flow and the corresponding temperature field were simulated and analyzed. Finally, a single-pipe injection steam disinfection verification test was performed for different SP sizes. The test results show that for the clay soil in the Yangtze River Delta region of China, the test temperature filed results are consistent with the simulation results when the heat flow reaches H = 20 cm in the vertical direction, the simulation and test result of the heat flow in the maximum horizontal diffusion distance are L = 13 cm and 12 cm, respectively. At the same disinfection time, the simulated soil temperature change trend is consistent with the test results, and the test temperature is lower than the simulated temperature. The difference between the theoretical temperature and the experimental temperature may be attributed to the heat loss in the experimental device. Further, it is necessary to optimize the CFD simulation process and add the disintegration and deformation processes of soil particle size with the change of water content. Furthermore, the soil pores increase as the SP size increases and that a large amount of steam vertically diffuses along the macropores and accumulates on the soil surface, causing ineffective heat loss. Moreover, soil temperature distribution changes from oval (horizontal short radius/vertical long radius = 0.65) to irregular shape. As the SP size decreases, the soil pore flow path becomes fine; the steam primarily diffuses uniformly around the soil in the form of a matrix flow; the diffusion distance in the horizontal direction gradually increases; and the temperature distribution gradually becomes even, which is consistent with the soil temperature field simulation results. Similar to the energy consumption analysis, the maximum energy consumption for SP sizes>27mm and <2mm was 486and 477kJ, respectively. Therefore, proper pore growth was conducive to the diffusion of steam, but excessive pores cause steam to overflow, which increased energy consumption of the system. Considering that the test was carried out in an ideal soil environment, the rotary tiller must be increased for fine rotary tillage in an actual disinfection operation. Although large particles may appear during the rotary tillage process, an appropriate number of large particles contributes to the formation of a large pore flow, under the common effect of matrix flow, it will simultaneously promote greater steam diffusion and heating efficiency. The above theoretical research has practical guiding significance for improving the design and disinfection effect of soil steam sterilizers in the future.

The most important factor impacting wheat production is water stress that occurs during the reproductive growth stage. Therefore, the plant responses and water productivity as affected by drought priming were investigated during Rabi seasons 2021 and 2022. The field trials were conducted in the research field of the Department of Irrigation and Drainage, Faculty of Agricultural Engineering, Sindh Agriculture University, Tandojam. The Hamal-BNS wheat variety was subjected to differing irrigation water regime levels (40%, 50% and 60% of soil water holding capacity, SWHC) after being subjected to drought priming, irrigation water recovery (water closure period) and drought priming. There were six treatments: (1) DPP-40 (drought priming plants at 40% of SWHC), (2) DPP-50, (3) DPP-60, (4) CTP-40 (controlled treated plants at 40% of SWHC), (5) CTP-50 and (6) CTP-60. During the experiment period, soil moisture content was significantly affected by the different treatments at various growth stages of wheat. The results indicated that winter wheat pre-exposed to drought priming attained a stress imprint that improved the subsequent deficit water levels which occurred during the later plant growth stage as demonstrated by the progress of test weight, grain yield, plant level water use efficiency and irrigation water use efficiency as well as relative yield compared to CTP-50 (control treatment). Under the irrigation water regime levels during the post-anthesis period, primed wheat plants sustained grain yield and higher relative yield than wheat plants without priming due to the better irrigation water regime for drought-primed wheat plants. Similarly, primed wheat plants consumed 18.3% less irrigation water as compared to non-primed plants, which significantly increased plant level WUE and irrigation WUE and decreased dry biomass and root development of drought-primed wheat plants. Therefore, to conserve fresh water for other field crops and increase water productivity in the Sindh province, it is recommended that drought priming is used during the early growth period of wheat plants as a successful irrigation method.

Optimization of chanterelle mushroom drying kinetics under heat pump dryer using Taguchi design method

There are so many factors that contribute to water stress, including poor management of water distribution. These fluctuations are important to be known, as the properties of lake and river shores are significantly affected by the changes in water levels. An automatic water level recorder in this condition is essential for proper distribution of water to the fields, and for researchers to get the data via mobile. A system comprising of an Arduino Nano (open source), water-level sensor (float/magnetic sensor and ultrasonic sensor), and GSM module was proposed in this study to monitor the water level of a water body. The device performed very well in both good network areas, and bad network areas with an R2value of 1.0 for the float sensor, and 0.9996 for the ultrasonic sensor. All the sensors were reliable and accurate, whereas in case of bad network areas the SMS received was delayed at an average of 5.7 minutes. This delay can only cause some issues whenthe data is needed on an immediate basis. The study concluded that the device built is reliable and can be used for the real-time monitoring of water levels.