The development of the world economy goes hand in hand with increased energy consumption and global warming caused by greenhouse gases. These issues can be tackled by implementing promising technologies of power generation. They differ from the known ones in that new energy resources are involved, e.g., mixtures of various types of biomass, provided that hazardous gas emissions during the production process are minimized. The development of high-potential energy-efficient and environmentally friendly technologies which use biofuel in the energy industry requires scientific evidence for the mechanisms, conditions, and characteristics of physical and chemical processes during pyrolysis and gasification of biomass, including its multicomponent types. This article analyzes the world technologies and research findings in the field of biomass pyrolysis and gasification. The effect of a group of factors on the intensity and completeness of gasification and pyrolysis of biofuel compositions has been determined. These factors include the size, shape, and surface structure of biomass particles; component composition and properties of fuel mixtures; mechanism and intensity of heat supply; and the temperature field in the reactor filled with solid and gaseous products. The most effective values of these characteristics have been established.
The article discusses the modern achievements in the field of thermal recovery of industrial and municipal waste. The average accumulation rate and calorific value of typical wastes were analyzed. The focus is on the opportunities to exploit the energy potential of high-moisture waste, low-grade liquid components, and fuel slurries. We consider the relevant results in the field of combustion, pyrolysis, and gasification of such fuels. The main attention is paid to synergistic effects, the influence of additives, and external conditions on the process performance. Vortex combustion chambers, boilers with burners, and nozzles for fuel injection, grate, and fluidized bed boilers can be used for the combustion of waste-derived liquid, high-moisture, and slurry fuels. The following difficulties are possible: long ignition delay, incomplete combustion, low combustion temperature and specific calorific value, high emissions (including particulate matter, polycyclic aromatic hydrocarbons), fast slagging, and difficult spraying. A successful solution to these problems is possible due to the use of auxiliary fuel; boiler modifications; oxy-fuel combustion; and the preparation of multi-component fuels, including the use of additives. An analysis of methods of waste recovery in the composition of slurries for fuel gas production showed that there are several main areas of research: pyrolysis and gasification of coal–water slurry with additives of oil waste; study of the influence of external conditions on the characteristics of final products; and the use of specialized additives and catalysts to improve the efficiency of the pyrolysis and gasification. The prospects for improving the characteristics of thermochemical conversion of such fuels are highlighted.
Experiments on the dissociation of a mixed gas hydrate in various combustion methods are performed. The simultaneous influence of two determining parameters (the powder layer thickness and the external air velocity) on the efficiency of dissociation is studied. It has been shown that for the mixed hydrate, the dissociation rate under induction heating is 10–15 times higher than during the burning of a thick layer of powder, when the combustion is realized above the layer surface. The minimum temperature required for the initiation of combustion for different combustion methods was studied. As the height of the sample layer increases, the rate of dissociation decreases. The emissions of NOx and CO for the composite hydrate are higher than for methane hydrate at the same temperature in a muffle furnace. A comparison of harmful emissions during the combustion of gas hydrates with various types of coal fuels is presented. NOx concentration as a result of the combustion of gas hydrates is tens of times lower than when burning coal fuels. Increasing the temperature in the muffle furnace reduces the concentration of combustion products of gas hydrates.
The main anthropogenic emissions (CO, CO2, NOx, SOx) produced by the processing (combustion) of wastes (coal filter cakes) were measured directly for the first time. The research considered the most widespread coal filter cakes: those of nonbaking, low-caking, coking, flame, and gas coals. These filter cakes are regarded as promising components for the technologies of coal-water slurry (CWS) and coal-water slurry containing petrochemicals (CWSP). According to our estimates, the annual increment of such wastes in the world is as high as 100 million tons. Consequently, the effective utilization of these wastes in the power industry is of high interest. The evaluation of hazardous emissions from the combustion of such wastes shows that filter cakes produce a similar amount of CO and CO2 as the initially-used coals but filter cakes are more cost-effective. We have established that CWS and CWSP technologies can be used to reduce NOx and SOx emissions. To reduce CO and CO2 emissions when burning filter cakes, we need to switch to low-temperature combustion. Lowering the combustion temperature of filter cakes from 850 °C down to 650 °C decreases the underburning insignificantly while decreasing CO and CO2 emissions by 30–40%.