Pollutants derived from real textile wastewater present a high environmental risk. This work involves the study of the removal of chemical oxygen demand (COD), color, and turbidity from Tunisian real textile wastewater by two different water treatment technologies: chemical coagulation (CC) and electrocoagulation (EC). A comparative study between these two methods was conducted based on the separation performance and operating cost (OC). The effects of different operational parameters including electrolysis time (t), voltage, and pH for EC and the coagulant concentration, initial pH, and time of slow mixing (t _sm) for CC were studied using response surface methodology. The developed quadratic models for the responses were in good agreement with the experimental data. The experiments proved the efficiency of both chemical and electrochemical techniques for the treatment of textile effluent. Indeed, by using EC, the reduction efficiencies of COD, color, and turbidity were 63.05, 99.07, and 96.31%, respectively, under optimal conditions (pH 9, t = 36.26 min, and voltage 4 V). For CC treatment, the achieved removal efficiencies of COD, color, and turbidity were 54.02, 96.21, and 93.7%, respectively, at pH 8.57, a coagulant concentration of 204.75 mg/L, and a t _sm of 28.41 min as optimal operating conditions. The OC obtained for EC and CC was about 0.47 and 0.2 USD/m³, respectively. Even if the OC of the EC process was higher as compared to the CC process, the treated water obtained by EC meets the Tunisian Standards (NT 106.03 and NT 09-14) for textile wastewater discharge into the environment and demonstrates a high potential for its reuse in various industrial activities. EC technology can be integrated into a wastewater management system that ensures a zero liquid discharge of wastewater into the environment.

This paper presents the impact on energy performance and visual comfort of retrofitting photovoltaic integrated shading devices (PVSDs) to the façade of a prototype office building in a hot desert climate. EnergyPlus™ and the DIVA-for-Rhino© plug-ins were used to perform numerical simulations and parametric analyses examining the energy performance and visual comfort of five configurations, namely: (1) inclined single panel PVSDs, (2) unfilled eggcrate PVSDs, (3) a louvre PVSD of ten slats tilted 30° outward, (4) a louvre PVSD of five slats tilted 30° outward, and (5) an STPV module with 20% transparency which were then compared to a reference office building (ROB) model. The field measurements of an off-grid system at various tilt angles provided an optimum tilt angle of 30°. A 30° tilt was then integrated into some of the PVSD designs. The results revealed that the integration of PVSDs significantly improved overall energy performance and reduced glare. The unfilled eggcrate PVSD did not only have the highest conversion efficiency at ȵ 20% but generated extra energy as well; an essential feature in the hot desert climate of Saudi Arabia.

Buildings consume considerable amount of energy to maintain comfortable interior. By allowing daylight, visual comfort inside a building is possible which can enhance the occupant’s health, mood and cognitive performance. However, traditional highly transparent windows should be replaced with semitransparent type window to attain a comfortable daylight inside a building. Evaluation of visual comfort includes both daylight glare and colour comfort analysis. Building integrated photovoltaic (BIPV) type windows are promising systems and can possess a range of semitransparent levels depending on the type of PV used. In this work, the semitransparent Perovskite BIPV windows was investigated by employing daylight glare analysis for an office building located in Riyadh, KSA and three wavelength dependent transmission spectra for colour comfort analysis. The results showed that the transmissions range between 50–70% was optimum for the comfortable daylight for south facing vertical pane BPV-windows. However, excellent colour comfort was attained for the transmission range of 90% which provided glare issues. Colour comfort for 20% transparent Perovskite was compared with contemporary other type of PV which clearly indicated that wavelength dependent transmittance is stronger over single value transmittance.