Understanding the structural properties of lignite during hydrothermal treatment would aid in predicting the subsequent behavior of coal during the pyrolysis, liquefaction, and gasification processes. Here, hydrothermal treatment of Inner Mongolia lignite (IM) was carried out in a lab autoclave. The distribution of carbon in the lignite was monitored via solid ¹³C nuclear magnetic resonance spectroscopy, and the functional groups of oxygen in lignite were determined by Fourier transform infrared spectroscopy. The curve-fitting method was used to calculate the content of the functional groups quantitatively. The results show that hydrothermal treatment is an effective method for upgrading the lignite. The side chains of the aromatic ring in lignite are altered, while the main macromolecular structure remains nearly the same. The hydrothermal treatment of IM could be divided into three temperature-dependent stages. The first stage (< 493 K) is the decomposition reaction of oxygen functional groups, where the O/C ratio decreases from 0.203 in raw IM to 0.185 for the IM treated at 493 K. In the second stage (493–533 K), hydrolysis of functional groups and hydrogen transfer between water and lignite occur. Here, the ratio of methylene to methyl increases from 0.871 in IM-493 to 1.241 for IM-533, and the content of quinone generates from the condensation of free phenol increased. The third stage (> 533 K) involves breakage of the covalent bond, and the content of CH₄ and CO in the emission gas clearly increase.

The thermo-chemical conversion of biomass wastes is a practical approach for the value-added reclamation of bioenergy in large quantities, and pyrolysis plays a core role in this process. In this work, poplar (PR) and cedar (CR) were used as staple wood biomasses to investigate the apparent kinetics of TG/DTG at different heating rates. Secondly, miscellaneous wood chips (MWC), in which PR and CR were mixed in equal proportion, were subjected to comprehensive investigations on their pyrolysis behavior and product evolution in a fixed bed reactor with pyrolysis temperature, catalyst, and the flow rate H₂O steam as influencing factors. The results demonstrated that both PR and CR underwent three consecutive pyrolysis stages, the TG/DTG curves shifted to higher temperatures, and the peak temperature intervals also enhanced as the heating rate increased. The kinetic compensation effect expression and apparent reaction kinetic model of CR and PR pyrolysis were obtained based on the law of mass action and the Arrhenius equation; the reaction kinetic parameter averages of Ea and A of its were almost the same, which were about 72.38 kJ/mol and 72.36 kJ/mol and 1147.11 min⁻¹ and 1144.39 min⁻¹, respectively. The high temperature was beneficial for the promotion of the pyrolysis of biomass, increased pyrolysis gas yield, and reduced tar yield. This process was strengthened in the presence of the catalyst, thus significantly increasing the yield of hydrogen-rich gas to 117.9 mL/g_-biomass. It was observed that H₂O steam was the most effective activator for providing a hydrogen source for the whole reaction process, promoted the reaction to proceed in the opposite direction of H₂O steam participation, and was beneficial to the production of H₂ and other hydrocarbons. In particular, when the flow rate of H₂O steam was 1 mL/min, the gas yield and hydrogen conversion were 76.94% and 15.90%, and the H₂/CO was 2.07. The yields of H₂, CO, and CO₂ in the gas formation were significantly increased to 107.35 mL/g_-biomass, 53.70 mL/g_-biomass, and 99.31 mL/g_-biomass, respectively. Therefore, H₂ was the most dominant species among gas products, followed by C-O bond-containing species, which provides a method for the production of hydrogen-rich gas and also provides ideas for compensating or partially replacing the fossil raw material for hydrogen production.

It is important to clarify the distribution of pyrolysis products from lignocellulosic biomass for its thermal transformation to produce high-quality bio-oil. Influences of the reaction temperature and catalysts on the pyrolysis product distribution from aspen wood (AW) and rice husk (RH) were studied by pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS). The difference in components from the lignocellulosic biomass results in different pyrolysis characteristics of the biomass raw materials. The reaction temperature significantly influences the product distribution from AW and RH pyrolysis. In all AW catalysis experiments, acids (8.35%), ketones (3.79%), phenols (4.73%), and esters (1.50%) have the lowest content while carbohydrates (48.75%) demonstrate the highest content when taking zinc chloride (ZnCl₂) as the catalyst; the HZSM-5 molecular sieve (HZSM-5) promotes the generation of esters (7.97%) and N-compounds (22.43%) while inhibiting production of aldehydes (2.41%); addition of an MCM-41 molecular sieve (MCM-41) is conducive to increasing the contents of aldehydes (21.29%), furans (5.88%), ketones (22.30%), acids (20.46%), and hydrocarbons (4.85%), while reducing the contents of alcohols (0) and carbohydrates (0). In all RH catalysis experiments, the addition of ZnCl₂ helps increase the content of carbohydrates (39.16%) and decrease the contents of ketones (3.89%), phenols (5.20%), alcohols (2.34%), esters (1.13%), and N-compounds (3.09%); when applying HZSM-5 as the catalyst, hydrocarbons (18.28%) and alcohols (6.66%) reach their highest content while acids (13.21%) have the lowest content; MCM-41 promotes the generation of aldehydes (25.33%) and furans (5.55%) while inhibiting that of carbohydrates (1.42%).