This letter presents a compact and wideband passive CMOS circulator for mmWave phased array transceivers. The letter focuses on achieving a compact die area while still offering competitive performance in terms of loss, isolation, and linearity. Our implemented circulator includes two reciprocal phase shift branches as well as a single-path nonreciprocal phase shift branch. We propose to use first-order lattice all-pass filters with coupled inductors to create the required phase shifts, which offer more compact, wideband, and predictable results compared to conventional lattice all-pass filters with two separate inductors. We also propose to use four identical first-order lattice cells in reciprocal and nonreciprocal branches. This can further reduce the size of the nonreciprocal branch due to fewer inductors compared to a typical second-order all-pass filter like bridged-T. The circuit is implemented in a 28 nm CMOS process, and the active die area is only 0.17 $\text{mm}^\text{2}$ . Our measurements demonstrate that the implemented circulator operates over a 1 dB insertion loss bandwidth of 14–28 GHz that achieves 66% fractional bandwidth with an insertion loss of 3.8 dB, isolation of over 20 dB, and input third-order intercept point of $+$ 19 dBm.
This manuscript presents two novel low-power high-speed true-single-phase-clock (TSPC) prescalers with division ratios of 2/3 and 4/5, respectively, in a standard 90-nm CMOS technology. The logic gates incorporated between the D-flip-flops (DFFs) of a conventional 2/3 prescaler are modified to reduce the propagation delay and hence increase the maximum operating frequency. The measurement results show that the proposed divide-by-2/3 and divide-by-4/5 prescalers can operate up to 17 GHz and 15.3 GHz, respectively, which increase by 5.4 GHz and 4.3 GHz compared with conventional TSPC prescalers. The power of the proposed divide-by-2/3 prescaler is 0.67 mW and 0.92 mW, and 0.87 mW and 1.06 mW for the proposed divide-by-4/5 prescaler. The chip occupies an area of 20 × 35 μm2 and 20 × 50 μm2 for the proposed divide-by-2/3 and divide-by-4/5 prescalers.
A circulator, which is a non-reciprocal device, is widely used in full-duplex systems, future communication and sensing networks, and quantum computing, and it is difficult to implement a passive topology on a chip. Based on switch-based spatio-temporal conductivity modulation, in this study, we design and implement a non-magnetic on-chip passive circulator operating at the Ku band in a 90-nm bulk CMOS technology using a 25% duty-cycle I/Q clock signal. With the virtue of the four-phase non-overlapping clock signal, the proposed circulator achieves a 3.9 dB transmitter (TX)-to-antenna (ANT) and a 4.0 dB ANT-to-receiver (RX) insertion loss with a 1-dB bandwidth of 2.7 GHz (21.4%). The TX-to-RX isolation is better than 17.2 dB, and the TX-to-ANT IIP3 and ANT-to-RX IIP3 are 19.7 dBm and 20.0 dBm, respectively, while occupying a die area of 1.55 mm × 1.15 mm. Although low-cost bulk CMOS technology is used, competitive isolation, linearity performance, and isolation bandwidth are achieved in the proposed design.
A four-channel receiver front-end is designed and implemented for interference- and jamming-robust global navigation satellite system (GNSS) in a 0.18-μm CMOS technology. The front-end consists of four identical RF-to-IF signal paths including low-noise amplifiers (LNAs), mixers and IF amplifiers. In addition, it also includes a phase-locked loop (PLL), which synthesizes the local oscillator (LO) signal, and a serial peripheral interface (SPI) for parameter adjustment. To improve the interference and jamming robustness, a novel linearity improvement technology and LO duty cycle adjustment method are applied in LNA and mixer design, respectively. The receiver achieves a gain of 40 dB, an input-referred third-order intercept point (IIP3) of −8 dBm and a jammer-to-signal power ratio (JSR) of 72 dB under 1.8-V and 3.3-V supply, while occupying a 4 × 5 mm2 die area including the electrostatic discharge (ESD) I/O pads.