This letter presents a low-noise amplifier (LNA) for multiband satellite communication (SATCOM) applications, featuring a wide effective bandwidth ($\text{BW}_{\text {eff}}$ ). Based on a feedback cascode structure, the design methodology to achieve wideband input matching in a multistage LNA is presented. A compact input matching network consisting of a parallel capacitor and a weakly coupled transformer is introduced to generate three distinct peaks in $S\!_{11}$ , effectively covering the 3-dB bandwidth ($\text{BW}_{3\,\text {dB}}$ ) of the LNA. The fabricated LNA demonstrates a peak gain of 21.2 dB with a $\text{BW}_{3 \,\text {dB}}$ from 5 to 25.7 GHz while consuming 16 mW. The noise figure (NF) remains within the range of 2.6–3.8 dB. $S\!_{11}$ and $S\!_{22}$ are better than –10 dB across 5.2–28 GHz. To the best of the authors’ knowledge, the FoMs of this work are one of the best results reported for CMOS LNAs with such a wide bandwidth.
This paper presents a multi-band low-noise amplifier (LNA) in the 45-nm CMOS silicon-on-insulator (SOI) process. The LNA consists of three stages, with the differential cascode amplifier as the core structure. The first stage is mainly responsible for input matching to ensure favourable noise characteristics and bandwidth, while the subsequent stages increase the gain. Moreover, the LNA utilizes baluns for input/output and interstage impedance matching. Switch capacitances are added to switch the three operating bands of the LNA, which cover 17–38 GHz overall. Measurement results show that the proposed LNA achieves a gain (S21) of 23.0 dB and a noise figure (NF) of 4.0 dB.
This paper presents a differential 19.6–39.4 GHz broadband low-noise amplifier (LNA) in 65-nm CMOS technology. The LNA consists of two cascode stage and one common-source stage. To achieve a wide bandwidth and low average noise figure, inter-stage peak-gain distribution technique and transformer-based triple-coupled technique are developed. Besides, a new compact T-coil-based network is proposed to neutralize the parasitic capacitors and enlarge the gain. The measure results show that the 3-dB bandwidth is from 19.6 to 39.4 GHz, the maximum gain is 23.5 dB, and the noise figure (NF) is from 3.7 to 5.8 dB. The dc power comsumption is 46 mW with 1V supply voltage. The input P1dB is −17 dBm at 30 GHz.
24 September 2025 in IEEE Transactions on Circuits and Systems II: Express Briefs
A broadband high dynamic range software-defined receiver is presented for X and Ku band applications. An adaptive RF front-end achieves precise gain control through a co-designed attenuator-LNA circuit and a noise canceling low-noise transconductance amplifier (LNTA). A 50%-LO-driven passive I/Q mixer combined with cross-coupled capacitive-feedback TIAs are employed to improve out-of-band linearity and blocker tolerance. Moreover, harmonic rejection of the LO is improved by adopting a quadrature generation circuit based on RC-CR network. Fabricated in a 55-nm CMOS process, the proposed receiver exhibits an adjustable gain of 10–57.7 dB, and a NF of 4.6–7.4 dB across 7.2–16 GHz. The design offers programmable channel bandwidth from 100 to 500 MHz, achieving 7.6 dBm in-band IIP3 and 14.4 dBm out-of-band IIP3 at 100 MHz channel bandwidth. Additionally, the I/Q outputs achieve an image rejection ratio exceeding 35 dB.
A circulator, which is a non-reciprocal device, is widely used in full-duplex systems, future communication and sensing networks, and quantum computing, and it is difficult to implement a passive topology on a chip. Based on switch-based spatio-temporal conductivity modulation, in this study, we design and implement a non-magnetic on-chip passive circulator operating at the Ku band in a 90-nm bulk CMOS technology using a 25% duty-cycle I/Q clock signal. With the virtue of the four-phase non-overlapping clock signal, the proposed circulator achieves a 3.9 dB transmitter (TX)-to-antenna (ANT) and a 4.0 dB ANT-to-receiver (RX) insertion loss with a 1-dB bandwidth of 2.7 GHz (21.4%). The TX-to-RX isolation is better than 17.2 dB, and the TX-to-ANT IIP3 and ANT-to-RX IIP3 are 19.7 dBm and 20.0 dBm, respectively, while occupying a die area of 1.55 mm × 1.15 mm. Although low-cost bulk CMOS technology is used, competitive isolation, linearity performance, and isolation bandwidth are achieved in the proposed design.
A four-channel receiver front-end is designed and implemented for interference- and jamming-robust global navigation satellite system (GNSS) in a 0.18-μm CMOS technology. The front-end consists of four identical RF-to-IF signal paths including low-noise amplifiers (LNAs), mixers and IF amplifiers. In addition, it also includes a phase-locked loop (PLL), which synthesizes the local oscillator (LO) signal, and a serial peripheral interface (SPI) for parameter adjustment. To improve the interference and jamming robustness, a novel linearity improvement technology and LO duty cycle adjustment method are applied in LNA and mixer design, respectively. The receiver achieves a gain of 40 dB, an input-referred third-order intercept point (IIP3) of −8 dBm and a jammer-to-signal power ratio (JSR) of 72 dB under 1.8-V and 3.3-V supply, while occupying a 4 × 5 mm2 die area including the electrostatic discharge (ESD) I/O pads.