Model based process development using predictive mechanistic models is a powerful tool for in-silico downstream process development. It allows to obtain a thorough understanding of the process reducing experimental effort. While in pharma industry, mechanistic modeling becomes more common in the last years, it is rarely applied in food industry. This case study investigates risk ranking and possible optimization of the industrial process of purifying lactoferrin from bovine milk using SP Sepharose Big Beads with a resin particle diameter of 200 µm, based on a minimal number of lab-scale experiments combining traditional scale-down experiments with mechanistic modeling. Depending on the location and season, process water pH and the composition of raw milk can vary, posing a challenge for highly efficient process development. A predictive model based on the general rate model with steric mass action binding, extended for pH dependence, was calibrated to describe the elution behavior of lactoferrin and main impurities. The gained model was evaluated against changes in flow rate, step elution conditions, and higher loading and showed excellent agreement with the observed experimental data. The model was then used to investigate the critical process parameters, such as water pH, conductivity of elution steps, and flow rate, on process performance and purity. It was found that the elution behavior of lactoferrin is relatively consistent over the pH range of 5.5 to 7.6, while the elution behavior of the main impurities varies greatly with elution pH. As a result, a significant loss in lactoferrin is unavoidable to achieve desired purities at pH levels below pH 6.0. Optimal process parameters were identified to reduce water and salt consumption and increase purity, depending on water pH and raw milk composition. The optimal conductivity for impurity removal in a low conductivity elution step was found to be 43 mS/cm, while a conductivity of 95 mS/cm leads to the lowest overall salt usage during lactoferrin elution. Further increasing the conductivity during lactoferrin elution can only slightly lower the elution volume thus can also lead to higher total salt usage. Low flow rates during elution of 0.2 column volume per minute are beneficial compared to higher flow rates of 1 column volume per minute. The, on lab-scale, calibrated model allows predicting elution volume and impurity removal for large-scale experiments in a commercial plant processing over 106 liters of milk per day. The successful model extrapolation was possible without recalibration or detailed knowledge of the manufacturing plant. This study therefore provides a possible pathway for rapid process development of chromatographic purification in the food industries combining traditional scale-down experiments with mechanistic modeling.
Protein A affinity chromatography is an important step in the purification of monoclonal antibodies (mAbs) and mAb‐derived biotherapeutics. While the biopharma industry has extensive expertise in the operation of protein A chromatography, the mechanistic understanding of the adsorption/desorption processes is still limited, and scaling up and scaling down can be challenging because of complex mass transfer effects in bead‐based resins. In convective media, such as fiber‐based technologies, complex mass transfer effects such as film and pore diffusions do not occur which facilitates the study of the adsorption phenomena in more detail and simplifies the process scale‐up. In the present study, the experimentation with small‐scale fiber‐based protein A affinity adsorber units using different flow rates forms the basis for modeling of mAb adsorption and elution behavior. The modeling approach combines aspects of both stoichiometric and colloidal adsorption models, and an empirical part for the pH. With this type of model, it was possible to describe the experimental chromatograms on a small scale very well. An in silico scale‐up could be carried out solely with the help of system and device characterization without feedstock. The adsorption model could be transferred without adaption. Although only a limited number of runs were used for modeling, the predictions of up to 37 times larger units were accurate.
Triggering the interaction of nanomaterials with molecules by means of electrical potentials in aqueous media remains challenging, especially if 3D through-flow systems are used as electrodes, as in potential-controlled liquid chromatography (PCC). In this paper, multi-walled carbon nanotubes (MWCNTs) function as a particulate packed bed electrode in order to study the system’s response to various applied potentials and electrolyte compositions. The process principle was analyzed using chronoamperometry and cyclic voltammetry. Applying an electrical potential to the hydrophilic MWCNTs induces the presence of both capacitive and faradaic currents. This leads, over time, to a degradation of the electrode due to structural changes of the MWCNT matrix and an increase in redox reactions on the surface. The role of the electrochemical double layer (EDL) is highlighted as a main player in the process, directly influencing the adsorption capability of the electrode. The EDL rearrangement time and coverage radius depend on the composition of the mobile phase and on the potential applied. The capacity of the electrode for the target (maleic acid) increases at high positive potentials (+800 mV vs. Ag/AgCl), while the presence of electrolytes leads to a capacity decrease. Our research enhances the understanding of capacitive through-flow cells.
The design of 3D monoliths provides a promising opportunity to scale the unique properties of singular carbon nanotubes to a macroscopic level. However, the synthesis of carbon nanotube monoliths is often characterized by complex procedures and additives impairing the later macroscopic properties. Here, we present a simple and efficient synthesis protocol leading to the formation of free-standing, stable, and highly conductive 3D carbon nanotube monoliths for later application in potential-controlled adsorption in aqueous systems. We synthesized monoliths displaying high tensile strength, excellent conductivity (up to 140 S m−1), and a large specific surface area (up to 177 m2 g−1). The resulting monoliths were studied as novel electrode materials for the reversible electrosorption of maleic acid. The process principle was investigated using chronoamperometry and cyclic voltammetry in a two-electrode setup. A stable electrochemical behavior was observed, and the synthesized monoliths displayed capacitive and faradaic current responses. At moderate applied overpotentials (± 500 mV vs. open circuit potential), the monolithic electrodes showed a high loading capacity (~20 µmol g−1) and reversible potential-triggered release of the analyte. Our results demonstrate that carbon nanotube monoliths can be used as novel electrode material to control the adsorption of small organic molecules onto charged surfaces.