Sasan Tavakoli

Dr. Sasan Tavakoli

Department of Mechanical Engineering, Aalto University, Espoo, Finland
orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 June 2023 in Journal of Fluid Mechanics
Verified
Journal Article
Open access
PDF file
Sasan TavakoliSasan Tavakoli
Sasan Tavakoli
Tommi Kristian MikkolaTommi Kristian Mikkola
Tommi Kristian Mikkola
Spyros E. HirdarisSpyros E. Hirdaris
Spyros E. Hirdaris
The paper presents a Fluid Structure Interaction (FSI) method for hydroelastic water entry. The method assumes that the momentum exchange between the fluid and solid body can be used for the calculation of pressure, deformation and stresses arising during impact. The flexible fluid–structure interactions of flat plates entering water are solved using a computational code that employs the finite volume method to discretise both fluid and solid equations. This provides a better matching of momentum on the fluid–solid interface. The momentum arising in the solid body that emerges after the impact is defined as the momentum exchange, and is shown to increase linearly under the increase of non-dimensional impact speed. The ratio of the maximum pressure arising in an elastic body entering water to that of a rigid body is termed relative pressure and is shown to decrease linearly as a function of momentum exchange. The latter verifies the main hypothesis of this paper, namely that ‘the pressure acting on an elastic body can be predicted using an unsophisticated equation that uses the momentum exchange.’ The deformation and stresses arising in elastic plates entering water are demonstrated to be functions of momentum exchange and can be found using simple equations formulated via parametrisation of data. It is concluded that subject to further validation, the method could be extended for the prediction of hydroelastic response of other sections/bodies entering water.

4 February 2025 in Renewable and Sustainable Energy Reviews
Verified
Journal Article
Open access
Aleksandr KondratenkoAleksandr Kondratenko
Aleksandr Kondratenko
MZMingyang Zhang
Mingyang Zhang
Sasan TavakoliSasan Tavakoli
Sasan Tavakoli
EAElias Altarriba
Elias Altarriba
Spyros E. HirdarisSpyros E. Hirdaris
Spyros E. Hirdaris

8 April 2024 in Ocean Engineering
Verified
Journal Article
Open access
Sasan TavakoliSasan Tavakoli
Sasan Tavakoli
MZMingyang Zhang
Mingyang Zhang
AKAleksander A. Kondratenko
Aleksander A. Kondratenko
SHSpyros Hirdaris
Spyros Hirdaris

22 September 2025 in Ocean Engineering
Verified
Journal Article
Open access
Sasan TavakoliSasan Tavakoli
Sasan Tavakoli
MSMansi Singh
Mansi Singh
SHSaeed Hosseinzadeh
Saeed Hosseinzadeh
ZHZhengyu Hu
Zhengyu Hu
Yanlin ShaoYanlin Shao
Yanlin Shao
Spyros E. HirdarisSpyros E. Hirdaris
Spyros E. Hirdaris

1 September 2016 in Applied Ocean Research
Verified
Journal Article
Closed access
PGParviz Ghadimi
Parviz Ghadimi
Sasan TavakoliSasan Tavakoli
Sasan Tavakoli
Abbas DashtimaneshAbbas Dashtimanesh
Abbas Dashtimanesh

Verified
Journal Article
Open access
PDF file
AHAzim Hosseini
Azim Hosseini
Sasan TavakoliSasan Tavakoli
Sasan Tavakoli
Abbas DashtimaneshAbbas Dashtimanesh
Abbas Dashtimanesh
PSPrasanta K. Sahoo
Prasanta K. Sahoo
Mihkel KõrgesaarMihkel Kõrgesaar
Mihkel Kõrgesaar
This paper presents CFD (Computational Fluid Dynamics) simulations of the performance of a planing hull in a calm-water condition, aiming to evaluate similarities and differences between results of different CFD models. The key differences between these models are the ways they use to compute the turbulent flow and simulate the motion of the vessel. The planing motion of a vessel on water leads to a strong turbulent fluid flow motion, and the movement of the vessel from its initial position can be relatively significant, which makes the simulation of the problem challenging. Two different frameworks including k-ε and DES (Detached Eddy Simulation) methods are employed to model the turbulence behavior of the fluid motion of the air–water flow around the boat. Vertical motions of the rigid solid body in the fluid domain, which eventually converge to steady linear and angular displacements, are numerically modeled by using two approaches, including morphing and overset techniques. All simulations are performed with a similar mesh structure which allows us to evaluate the differences between results of the applied mesh motions in terms of computation of turbulent air–water flow around the vessel. Through quantitative comparisons, the morphing technique has been seen to result in smaller errors in the prediction of the running trim angle at high speeds. Numerical observations suggest that a DES model can modify the accuracy of the morphing mesh simulations in the prediction of the trim angle, especially at high-speeds. The DES model has been seen to increase the accuracy of the model in the computation of the resistance of the vessel in a high-speed operation, as well. This better level of accuracy in the prediction of resistance is a result of the calculation of the turbulent eddies emerging in the water flow in the downstream zone, which are not captured when a k-ε framework is employed. The morphing approach itself can also increase the accuracy of the resistance prediction. The overset method, however, overpredicts the resistance force. This overprediction is caused by the larger vorticity, computed in the direction of the waves, generated under the bow of the vessel. Furthermore, the overset technique is observed to result in larger hydrodynamic pressure on the stagnation line, which is linked to the greater trim angle, predicted by this approach. The DES model is seen to result in extra-damping of the second and third crests of transom waves as it calculates the stronger eddies in the wake of the boat. Overall, a combination of the morphing and DES models is recommended to be used for CFD modeling of a planing hull at high-speeds. This combined CFD model might be relatively slower in terms of computational time, but it provides a greater level of accuracy in the performance prediction, and can predict the energy damping, developed in the surrounding water. Finally, the results of the present paper demonstrate that a better level of accuracy in the performance prediction of the vessel might also be achieved when an overset mesh motion is used. This can be attained in future by modifying the mesh structure in such a way that vorticity is not overpredicted and the generated eddies, emerging when a DES model is employed, are captured properly.