Small angle x-ray scattering was used to study the morphology of conical structures formed in thin films of amorphous SiO 2 . Samples were irradiated with 1.1 GeV Au ions at the GSI UNILAC in Darmstadt, Germany, and with 185, 89 and 54 MeV Au ions at the Heavy Ion Accelerator Facility at ANU in Canberra, Australia. The irradiated material was subsequently etched in HF using two different etchant concentrations over a series of etch times to reveal conically shaped etched channels of various sizes. Synchrotron based SAXS measurements were used to characterize both the radial and axial ion track etch rates with unprecedented precision. The results show that the ion energy has a significant effect on the morphology of the etched channels, and that at short etch times resulting in very small cones, the increased etching rate of the damaged region in the radial direction with respect to the ion trajectory is significant.
23 March 2022 in Physical Chemistry Chemical Physics
Here, we present new models to fit small angle X-ray scattering (SAXS) data for the characterization of ion tracks in polymers. Ion tracks in polyethylene terephthalate (PET), polycarbonate (PC), polyimide (PI) and polymethyl methacrylate (PMMA) were created by swift heavy ion irradiation using 197Au and 238U with energies between 185 MeV and 2.0 GeV. Transmission SAXS measurements were performed at the Australian Synchrotron. SAXS data were analysed using two new models that describe the tracks by a cylindrical structure composed of a highly damaged core with a gradual transition to the undamaged material. First, we investigate the ‘Soft Cylinder Model’, which assumes a smooth function to describe the transition region by a gradual change in density from a core to a matrix. As a simplified and computational less expensive version of the ‘Soft Cylinder Model’, the ‘Core Transition Model’ was developed to enable fast fitting. This model assumes a linear increase in density from the core to the matrix. Both models yield superior fits to the experimental SAXS data compared with the often-used simple ‘Hard Cylinder Model’ assuming a constant density with an abrupt transition.
9 March 2023 in Superconductor Science and Technology
Normal-incidence irradiation by 100 MeV Ag ions is used to improve flux pinning in previously optimised commercial REBCO tapes from the American Superconductor Corporation. We observe distinct critical-current anisotropy enhancements below and above 40 K. Above 40 K a strong c-axis peak appears in the angular dependence of the critical current, as is usually expected upon the introduction of columnar defects. The critical current is enhanced significantly but only for a limited range of field angles. Close to the parallel-field direction there is no enhancement or even a reduction in critical current. Below 40 K, on the other hand, the enhancement is much broader with respect to field angle, creating an almost isotropic response at 20 K, 3 T. The absence of a prominent c-axis peak does not indicate a lack of pinning, since the absolute value of the critical current still increases by a factor of 2.8 compared to an unirradiated sample. Instead, we postulate that pre-existing point-like pinning centres act to mediate an interaction between the existing planar and newly-introduced columnar pins, broadening both contributions. The point-like pins become less effective with increasing temperature as the coherence length increases, leading to a reduction in this interaction and a separation of the individual peaks relating to planar and columnar pins. At 20 K, we achieve an enhancement in the angular-minimum critical current by a factor of 2.7, in a material that had already been process-optimised for low-temperature pinning.
In situ small angle X-ray scattering (SAXS) measurements of ion track etching in polycarbonate foils are used to directly monitor the selective dissolution of ion tracks with high precision, including the early stages of etching. Detailed information about the track etching kinetics and size, shape, and size distribution of an ensemble of nanopores is obtained. Time resolved measurements as a function of temperature and etchant concentration show that the pore radius increases almost linearly with time for all conditions and the etching process can be described by an Arrhenius law. The radial etching shows a power law dependency on the etchant concentration. An increase in the etch rate with increasing temperature or concentration of the etchant reduces the penetration of the etchant into the polymer but does not affect the pore size distribution. The in situ measurements provide an estimate for the track etch rate, which is found to be approximately three orders of magnitude higher than the radial etch rate. The measurement methodology enables new experiments studying membrane fabrication and performance in liquid environments.