Diesel emissions have a significant impact on the atmosphere, contributing to air pollution, smog and global warming. As a result, diesel exhaust is dangerous to human health. While emissions reduction efforts have often focused on changing engine design or improving aftertreatment, diesel fuel modifications can also play an important role in improving engine efficiency and reducing exhaust emissions. The aim of this work was to examine the potential for emissions reductions under real-world conditions when employing fuel additives. Three different additives were examined, consisting of hydrotreated vegetable oil (HVO) and two commercial additives containing nanoparticles of cerium dioxide and ferrocene. HVO was selected as a renewable fuel, an alternative to commonly used biodiesels with competitive advantages. The new European driving cycle (NEDC) procedure was used to measure emissions of regulated compounds: carbon monoxide, nitrogen oxides, hydrocarbons and particulates (by mass and number) from an 11-year-old passenger car equipped with a diesel engine powered by fuel blends. The fuel blends prepared met the quality requirements for diesel fuel. The results obtained confirm that the application of both HVO and nano-additives to diesel can achieve a significant reduction of carbon monoxide (52%) and hydrocarbon (47%) emissions compared to the B7 base fuel. Particulate emissions (up to 10% by mass of particulates and 7% by number of particulates) were found to be best reduced by adding nanoparticles of cerium dioxide to the B7 fuel (with 30% HVO), while the best results in reducing nitrogen oxide emissions were obtained by adding ferrocene nanoparticles to the B7 fuel with 30% HVO.

The interest in chlorinated volatile organic compounds is not a new task but still draws the attention of scientists. The role they play in human organism, is an important aspect to consider, since the development of analytical techniques and instrumental solutions gives new possibilities of their application in the analytics of volatile compounds and recognition of properties, so far impossible to achieve. Regarded mostly as xenobiotics, these compounds become a challenge for analysts aiming at sample preparation, which will ensure a high value of the analyte's enrichment factor, its determination on the lowest possible concentration level, without excluding the quality of analytical results. Current contributions review issues of environmental fate of halogenated compounds with a special emphasis on chlorinated volatiles, their toxicity, and bioaccumulation in living organisms. Focusing on analytical techniques, overviews include several sampling, preconcentration, and detection methods exemplified by measurements in air, water, and other matrices, including living organisms (e.g., human breath).

As general trends in current development of chemical analysis, including electroanalysis, one can indicate a search for methods fast and multianalyte, for miniaturized measuring devices, mechanization and automation of analytical processes. In all these trends a significant role is played by measurements in flow conditions. The major advantage of flow electroanalysis is a possibility of utilizing a kinetic discrimination in potentiometric measurements and enhancement of mass transport in voltammetric techniques. Flow injection techniques provide shortening of time of a single analytical determination due to reproducible use of transient signal from the detector without need of obtaining a steady‐state equilibrium signal. Electrochemical detection in HPLC gives often improved selectivity and detection limit for electroactive solutes, whereas in capillary electrophoresis it allows a convenient design of portable, integrated chips for field application. This review presents state‐of‐the ‐art of flow electroanalysis based on 226 cited literature references

Additive manufacturing, enabling rapid prototyping and so-called on-demand production, has become a common method of creating parts or whole devices. On a 3D printer, real objects are produced layer by layer, thus creating extraordinary possibilities as to the number of applications for this type of devices. The opportunities offered by this technique seem to be pushing new boundaries when it comes to both the use of 3D printing in practice and new materials from which the 3D objects can be printed. However, the question arises whether, at the same time, this solution is safe enough to be used without limitations, wherever and by everyone. According to the scientific reports, three-dimensional printing can pose a threat to the user, not only in terms of physical or mechanical hazards, but also through the potential emissions of chemical substances and fine particles. Thus, the presented publication collects information on the additive manufacturing, different techniques, and ways of printing with application of diverse raw materials. It presents an overview of the last 5 years’ publications focusing on 3D printing, especially regarding the potential chemical and particle emission resulting from the use of such printers in both the working environment and private spaces.

Office devices can release volatile organic compounds (VOCs) partly generated by toners and inks, as well as particles of paper. The aim of the presented study is to identify indoor emissions of volatile halogenated organic compounds into the office workspace environment. Mixtures of organic pollutants emitted by seven office devices, i.e. printers and copiers, were analyzed by taking samples in laboratory conditions during the operation of these appliances. Tests of volatile organic compound emissions from selected office devices were conducted in a simulated environment (test chamber). Samples of VOCs were collected using three-layered thermal desorption tubes. Separation and identification of organic pollutant emissions were made using thermal desorption combined with gas chromatography coupled to mass spectrometry. Test chamber studies indicated that operation of the office printer and copier would contribute to the significant concentration level of VOCs in typical office indoor air. Among the determined volatile halogenated compounds, only chlorinated organic compounds were identified, inter alia: trichloroethylene — carcinogenic — and tetrachloroethylene — possibly carcinogenic to human. The results show that daily exposure of an office worker to chemical factors released by the tested printing and copying units can be variable in terms of concentrations of VOCs. The highest emissions in the test chamber during printing were measured for ethylbenzene up to 41.3 μg m⁻³, xylenes up to 40.5 μg m⁻³ and in case of halogenated compounds the highest concentration for chlorobenzene was 6.48 μg m⁻³. The study included the comparison of chamber concentrations and unit-specific emission rates of selected VOCs and the identified halogenated compounds. The highest amount of total VOCs was emitted while copying with device D and was rated above 1235 μg m⁻³ and 8400 μg unit⁻¹ h⁻¹ on average.

The paper presents the results of phthalates measurements in 4 companies producing or processing materials made of rubber and plastics. Six priority phthalates were determined in air samples both in the respirable and inhalable particle fractions. For the determination of phthalates, GC/MS was applied, which ensures the determination of the method at the level of 0.066 µg/m³ for fibreglass filter and polyurethane foam and 0.022 µg/m³ for Amberlite resin XAD-2, while taking 720 L of air samples. The results of the measurements showed that dimethyl phthalate, diethyl phthalate and dibutyl phthalate (DBP) dominated in all the investigated companies in the gaseous phase of air sampling. For example, in a company producing rubber details for car accessories, the concentration of DBP ranged from 54 to 74% of the total phthalate concentration determined in the gaseous phase. The inhalable particle fraction was dominated by two compounds, i.e. DBP and di(2-ethylhexyl) phthalate DEHP, and their total concentration was a significant percentage, on average over 83% of the sum of all phthalates determined in the inhalable fraction in the investigated companies. As particle size affects the location of phthalate deposition in the respiratory tract, the determination of concentration levels of individual phthalates in the gaseous phase and in inhalable and respirable fractions can provide valuable information that can be used to improve the health and safety of workers at work.