Accurate, high-resolution maps of for crop growth monitoring are strongly needed by precision agriculture. The information source for such maps has been supplied by satellite-borne radars and optical sensors, and airborne and drone-borne optical sensors. This article presents a novel methodology for obtaining growth deficit maps with an accuracy down to 5 cm and a spatial resolution of 1 m, using differential synthetic aperture radar interferometry (DInSAR). Results are presented with measurements of a drone-borne DInSAR operating in three bands—P, L and C. The decorrelation time of L-band for coffee, sugar cane and corn, and the feasibility for growth deficit maps generation are discussed. A model is presented for evaluating the growth deficit of a corn crop in L-band, starting with 50 cm height. This work shows that the drone-borne DInSAR has potential as a complementary tool for precision agriculture.
Differential synthetic aperture radar interferometry (DInSAR) has been widely applied since the pioneering space-borne experiment in 1989, and subsequently with the launch of the ERS-1 program in 1992. The DInSAR technique is well assessed in the case of space-borne SAR data, whereas in the case of data acquired from aerial platforms, such as airplanes, helicopters, and drones, the effective application of this technique is still a challenging task, mainly due to the limited accuracy of the information provided by the navigation systems mounted onboard the platforms. The first airborne DInSAR results for measuring ground displacement appeared in 2003 using L- and X-bands. DInSAR displacement results with long correlation time in P-band were published in 2011. This letter presents a SAR system and, to the best of our knowledge, the first accuracy assessment of the DInSAR technique using a drone-borne SAR in L-band. A deformation map is shown, and the accuracy and resolution of the methodology are presented and discussed. In particular, we have obtained an accuracy better than 1 cm for the measurement of the observed ground displacement. It is in the same order as that achieved with space-borne systems in C- and X-bands and the airborne systems in X-band. However, compared to these systems, we use here a much longer wavelength. Moreover, compared to the satellite experiments available in the literature and aimed at assessing the accuracy of the DInSAR technique, we use only two flight tracks with low time decorrelation effects and not a big data stack, which helps in reducing the atmospheric effects.
In synthetic aperture radar (SAR) imaging, the goal of subsurface tomography is to create detailed images of objects and structures underground. In order to obtain well-focused images, the refraction effect must be taken into account during SAR processing. This work proposes an adjusted back-projection algorithm and validates it with simulation and experimental results. The simulation model constitutes an underground air cavity and a multi-circular flight path. The experimental scenario includes a buried quad-corner reflector and an unmanned aerial vehicle (UAV) performing a spiral flight path. Both cases produced well-focused 3D images with the correct positioning of the targets.
This paper presents a fast factorized back-projection (FFBP) algorithm that can satisfactorily process real P-band synthetic aperture radar (SAR) data collected from a spiral flight pattern performed by a drone-borne SAR system. Choosing the best setup when processing SAR data with an FFBP algorithm is not so straightforward, so predicting how this choice will affect the quality of the output image is valuable information. This paper provides a statistical phase error analysis to validate the hypothesis that the phase error standard deviation can be predicted by geometric parameters specified at the start of processing. In particular, for a phase error standard deviation of ~12°, the FFBP is up to 21 times faster than the direct back-projection algorithm for 3D images and up to 13 times faster for 2D images.
This article presents a novel method for predicting the sugarcane harvesting date and productivity using a three-band imaging radar. Taking advantage of working with a multi-band radar, this system was employed to estimate the above-ground biomass (AGB), achieving a root-mean-square error (RMSE) of 2 kg m−2 in sugarcane crops, which is an unprecedented result compared with other works based on the Synthetic Aperture Radar (SAR) system. By correlating the field measurements of the ripening index (RI) with the AGB measurements by radar, an indirect estimate of the RI by the radar is obtained. It is observed that the AGB reaches its maximum approximately 280 days after planting and the maximum RI, which defines the harvesting date, approximately 360 days after planting for the species IACSP97-4039. Starting from an AGB map collected by the radar, it is then possible to predict the harvesting date and the corresponding productivity with competitive average errors of 8 days and 10.7%, respectively, with three months in advance, whereas typical methods employed on a test site achieve an average error of 30 days with three months in advance. To the best of our knowledge, it is the first time that a multi-band radar is employed for productivity prediction in sugarcane crops.
A sustainable future requires efficient water use in irrigated agriculture to ensure food and water security. The crop water stress index (CWSI) is a remote sensing tool that can help achieve this goal. In typical CWSI experiments, infrared sensors focus on the canopy to measure its temperature. This study evaluated this methodology for crop beans (Phaseolus vulgaris L.) with low canopy coverage. In this scenario, the temperature measurement is significantly affected by the presence of straw mulch. The study also proposed a procedure that uses supplementary data to estimate canopy coverage and straw mulch temperature. Then, the canopy temperature is finally estimated from the infrared sensor measurement. The procedure was successfully implemented for low canopy coverages. Without it, the baseline slope was inconsistent with the CWSI theory. This was particularly true during the earlier phenological stages. The lowest observed canopy coverage was 0.17 for the baseline and 0.26 when estimating the CWSI. The CWSI showed a clear relationship with soil water content.