caixia zhang

Dr. caixia zhang

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 March 2020 in Energies
Verified
Journal Article
Open access
PDF file
CZcaixia zhang
caixia zhang
HSHonglie Shen
Honglie Shen
LSLuanhong Sun
Luanhong Sun
JYJiale Yang
Jiale Yang
SWShiliang Wu
Shiliang Wu
ZLZhonglin Lu
Zhonglin Lu
In this paper, we report one bifacial p-type PERC solar cell with efficiency over 22% using laser doped selective emitter produced in larger-scale commercial line on 6-inch mono-crystalline wafer. On front side of the solar cell, square resistance of p-n junction was found to be closely related with laser power at certain laser scan speed and frequency. On the other side, the rear fingers with different ratios of height and width and rear silicon nitride (SiNx) layer with different thickness were optimized, and a highest rear efficiency of the bifacial solar cell was obtained. Finally, bifacial silicon solar cells with the front and rear efficiencies exceeding 22% and 15% (AM1.5, 1000 W/m2, 25 °C) were successfully achieved, respectively.

3 January 2023 in ACS Applied Energy Materials
Verified
Journal Article
Closed access
BLBeibei Lin
Beibei Lin
QSQuanzhen Sun
Quanzhen Sun
CZcaixia zhang
caixia zhang
HDHui Deng
Hui Deng
YLYaling Li
Yaling Li
SCShuying Cheng
Shuying Cheng

13 June 2022 in International Journal of Energy Research
Verified
Journal Article
Closed access
CZcaixia zhang
caixia zhang
HSHonglie Shen
Honglie Shen
HLHongzhi Liu
Hongzhi Liu
WZWei Zhang
Wei Zhang
JCJun Chen
Jun Chen
HLHua Li
Hua Li

1 November 2023 in Energies
Verified
Journal Article
Open access
PDF file
CZcaixia zhang
caixia zhang
HSHonglie Shen
Honglie Shen
HLHongzhi Liu
Hongzhi Liu
Compared with typical mono-facial photovoltaic (PV) solar modules, bifacial solar modules can make full use of reflected or scattered light from the ground and the surroundings to yield more electrical energy. The electrical energy on the rear side depends on multiple factors, such as the IV parameters of modules, packaging materials, and installation circumstances. In this work, the power generation output is simulated and researched using the PV-SYST software program, based on the different electrical parameters of bifacial solar modules and the installation conditions of the given PV systems. The influencing factors that affect the electrical energy are further analyzed using power-loss diagrams. The results show that improving the surface albedo can raise additional energy by 8.3%, thus behaving significantly better than the mono-facial module. Furthermore, improving the siting height and incidence angle modifier (IAM) of the modules can increase the additional energy by 3.1%. In contrast, adjusting the output current or voltage of the modules adds some energy, while the modules are of the same nominal power value. It was observed that the energy level of a photovoltaic system mainly depends on the installation circumstances, but the electrical parameters of the modules themselves contribute little.

1 October 2014 in Chinese Physics B
Verified
Journal Article
Closed access
CZcaixia zhang
caixia zhang
YNYu-Quan Niu
Yu-Quan Niu
QMQingtian Meng
Qingtian Meng

5 January 2022 in Semiconductor Science and Technology
Verified
Journal Article
Closed access
CZcaixia zhang
caixia zhang
HSHonglie Shen
Honglie Shen
JCJun Chen
Jun Chen
HLHua Li
Hua Li
Partial shading is very common in photovoltaic (PV) systems. The mismatch losses and hot-spot effects caused by partial shading can not only affect the output power of a solar system, but also can bring security and reliability problems. This paper centers on the silicon crystalline PV module technology subjected to operating conditions with some cells partially or fully shaded. A comparison of the electrical and hot-spot performance results for four different connection mode PV modules without shading and with partial or full shading is presented. Bypass diode of different modules would start up in the different conditions with increasing shading area. We found that the regular half-cell module degraded about 60% than its non-shaded power, which is about 30% less than the other three modules, when the short edges of these modules were shaded. The highest hot-spot temperature of the regular half-cell module was 75.5 °C, which is the lowest among the four modules before the diode started up.