Soft robotic grippers possess high structural compliance and adaptability, allowing them to grasp objects with unknown and irregular shapes and sizes. To enable more dexterous manipulation, soft sensors that are similar in mechanical properties to common elastomer materials are desired to be integrated into soft grippers. In this paper, we develop ionic hydrogel-based strain and tactile sensors and integrate these sensors into a three-finger soft gripper for learning-based object recognition and force-controlled grasping. Such hydrogel-based sensors have excellent conductivity, high stretchability and toughness, good ambient stability, and unique antifreezing property; they can be readily attached to a soft gripper at desired locations for strain and tactile sensing. By using a deep-learning model, the sensory soft gripper is demonstrated to be capable of grasping and recognizing objects at both room and freezing temperatures, and achieving close to 100% recognition accuracy for ten typical objects. Moreover, the capacitive tactile feedback of the gripper is utilized to develop a closed-loop force controller and realize force-controlled grasping of fragile or highly deformable objects. A new slip detection and compensation strategy is also proposed and validated for the sensory gripper for adjusting the grasping force in real time upon detecting slippage. Note to Practitioners —The multimodal sensation of a soft robotic gripper could enrich its grasping functionalities and improve its manipulation performance. This research integrates novel antifreezing ionic hydrogel-based strain and tactile sensors into a three-finger soft robotic gripper for learning-based object recognition and force-controlled grasping. Constructed from a highly stretchable, ambient-stable, and antifreezing ionic hydrogel, the strain and tactile sensors can be readily integrated at the desired locations on the soft gripper, and can reliably operate at both ambient and freezing temperatures with excellent mechanical and electrical properties. Based on the feedback of the strain and tactile sensors, a deep learning model is employed to enable high-accuracy object recognition while grasping, which can be useful for manipulation in vision-free environments. Closed-loop force control and slip compensation strategies are also demonstrated for reliably grasping fragile/deformable objects and handling slip events during the manipulation of heavy objects. The sensory soft gripper and the associated object recognition and force control methods could find practical applications in a variety of robotic manipulation tasks.
Denudation is a technique for removal of the cumulus cell mass from oocytes in clinical intracytoplasmic sperm injection (ICSI). Manual oocyte denudation requires long training hours and stringent skills, but still suffers from low yield rate and denudation efficiency due to human fatigue and skill variations across operators. To address these limitations, this paper reports a robotic system for automated oocyte denudation. In this system, several key techniques are proposed, including a vision-based contact detection method for measuring the relative z position between the micropipette tip and the dish substrate, recognition of oocytes and the surrounding cumulus cells, automated calibration algorithm for eliminating the misalignment angle, and automated control of the flow rate based on the model of oocyte dynamics during micropipette aspiration and deposition. Experiments on mouse oocytes demonstrated that the robotic denudation system achieved a high yield rate of 97.0 ± 2.8% and denudation efficiency of 95.0 ± 0.8%. Additionally, oocytes denuded by the robotic system showed comparable fertilization rate and developmental competence compared with manual denudation. Our robotic denudation system represents one step towards the automation and standardization of ICSI procedures.
2 February 2018 in IEEE Transactions on Nanotechnology
Electrospinning is a technique for creating continuous nanofibrous networks that can architecturally be similar to the structure of extracellular matrix (ECM). In this work, a simple and semi-automatic electrostatic spinning system is designed, and a method of multi-layer composite electrostatic spinning is adopted, which is called the hierarchical construction (Sandwich mode). Then a kind of PLGA/silk fibroin composite electrospinning nanofibrous scaffolds is proposed for the growth of skin cells in combination with the good characters of silk fibroin and PLGA. The SEM experiment of the silk fibroin/PLGA composite nanofibers indicated that the prepared nanofibers are smooth, uniform in size and have good porosity. The wrinkled contrast test is shown that this nanofiber scaffold remain flat in the culture medium as the original, and is basically not shrink. The water absorption experimental results show that the composite nanofiber scaffold has good hydrophilicity, and the water absorption increases with time is not obvious. The cell culture experiment is also shown that the skin cells can proliterate on the scaffold.
This paper reported a biaxial nanopositioning stage single-driven by piezoelectric motor. The employed piezoelectric motor can perform two different driving modes, namely, AC drive mode to drive in long-stroke and at high-speed and DC scanning mode with the high-resolution of several nanometers, which satisfies the requirements of both long-stroke and nanoresolution. To compensate for the effects of the variable friction force and some unpredictable disturbances, a novel backward error compensation (BEC) positioning control method integrated of the two driving modes and a double closed-loop PID controller system are proposed to obtain a high-accuracy positional motion. The experiment results demonstrate that the nanopositioning stage with large travel range of 300 mm × 300 mm has a fine speed characteristic and resolution is 5 nm. In the experiments of different travels up to 15 mm, calibrated by a commercial laser vibrometer, the positioning accuracy is proved within 55 nm inx-axis and 40 nm iny-axis with standard deviation less than 40 nm inx-axis and 30 nm iny-axis and the final position locking can be limited to 10 nm, meeting the requirements of micromanipulation technology.
Piezoelectric stick–slip drive nanopositioners are of central importance in in situ SEM nanorobotic systems due to their high precise positioning, large stroke, high speed, and compact structure. However, the output velocity under high load will be seriously influenced. In this paper, a new piezoelectric stick–slip drive nanopositioner with large velocity under high load by introducing the adjust bolts to decouple the driving unit and moving unit is presented. A MATLAB simulation model has been created to optimize the nanopositioner for a certain velocity, and a FEM is used to confirm that the leaf hinge has sufficient stiffness. The size of the prototype is 30 × 32 × 25 mm3. Testing results indicate that the nanopositioner achieves a maximum velocity of 3.467 mm/s and a minimum resolution of 6 nm. When the load increases from 0.4 kg to 2 kg, the maximum velocities only decrease from 3.457 mm/s to 3.143 mm/s. The proposed piezoelectric stick–slip nanopositioner shows large velocity under high load.
The piezoelectrically-actuated stick-slip nanopositioning stage (PASSNS) has been applied extensively, and many designs of PASSNSs have been developed. The friction force between the stick-slip surfaces plays a critical role in successful movement of the stage, which influences the load capacity, dynamic performance, and positioning accuracy of the PASSNS. Toward solving the influence problems of friction force, this paper presents a novel stick-slip nanopositioning stage where the flexure hinge-based friction force adjusting unit was employed. Numerical analysis was conducted to estimate the static performance of the stage, a dynamic model was established, and simulation analysis was performed to study the dynamic performance of the stage. Further, a prototype was manufactured and a series of experiments were carried out to test the performance of the stage. The results show that the maximum forward and backward movement speeds of the stage are 1 and 0.7 mm/s, respectively, and the minimum forward and backward step displacements are approximately 11 and 12 nm, respectively. Compared to the step displacement under no working load, the forward and backward step displacements only increase by 6% and 8% with a working load of 20 g, respectively. And the load capacity of the PASSNS in the vertical direction is about 72 g. The experimental results confirm the feasibility of the proposed stage, and high accuracy, high speed, and good robustness to varying loads were achieved. These results demonstrate the great potential of the developed stage in many nanopositioning applications.