The longitudinal vibration of the drill pipe contains considerable energy which can be used to improve the rock-breaking efficiency during drilling. It is very important to the development of drilling speed-up tools to have a comprehensive understanding of the energy conversion efficiency of downhole drill string vibration. In this paper, the characteristics of downhole bit load and longitudinal vibration of drill string under different conditions were studied in the experiment, and the analysis method of energy conversion efficiency from drill string vibration to spring potential energy was proposed. The experimental analysis showed that the fluctuation of the downhole bit load was reduced by 10%–90% after the spring was installed in the bottom hole assembly. The rotation rate and the spring elastic stiffness had a significant and positive influence on the fluctuation amplitude of the downhole bit load. Meanwhile, the longitudinal vibration amplitude and acceleration of the drill string peaked at the elastic stiffness of 1 kN/mm. The closer the spring position to the drill bit was, the more severe the longitudinal vibration of the drill string above the spring component was. The bit load and the rotation rate had a positive influence on the severity of longitudinal vibration. The analysis of energy conversion efficiency showed that the available mechanical energy range of the longitudinal vibration of the drill pipe was about 200–420 kW. The work power of the drill string vibration to the spring component increased sharply and then decreased with the increasing of elastic stiffness. The energy conversion efficiency came to the optimal value when the elastic stiffness was between 1 kN/mm and 2 kN/mm. Increasing the rotation rate, keeping the bit load below 134.5 kN and installing the spring component near the drill bit are beneficial for improving the energy conversion efficiency of drill string vibration. This paper reveals the main factors affecting the energy conversion efficiency of drill string vibration and their influencing laws, and determines the range of WOB, rotation speed, spring position and stiffness to obtain the best energy conversion efficiency.
Drilling-fluid loss has always been one of the challenging issues in the field of drilling engineering. This article addresses the limitations of a single fluid-loss pressure mechanism model and the challenges in predicting positive drilling-fluid-loss pressure. By categorizing fluid losses of various types encountered during drilling, different geological formations associated with distinct mechanisms are considered. The actual drilling-fluid density in the wellbore at the time of fluid-loss occurrence is taken as a reference value for calculating the positive drilling-fluid-loss pressure of the already drilled well. Building upon this foundation, a combined model utilizing the Sparrow Search Algorithm (SSA) and Long Short-Term Memory (LSTM) neural network is constructed. This model effectively explores the intricate nonlinear relationship between well logging, logging engineering data, and fluid-loss pressure. By utilizing both data from the already drilled wells and upper formation data from ongoing drilling, precise prediction of positive drilling formation fluid-loss pressure can be achieved. Case studies demonstrate that the approach established in this paper, incorporating upper formation data, reduces the average absolute percentage error of fluid-loss pressure prediction to 2.4% and decreases the root mean square error to 0.0405. Through the synergy of mechanistic models and data-driven techniques, not only has the accuracy of predicting positive drilling formation fluid-loss pressure has been enhanced, but also valuable insights have been provided for preventing and mitigating fluid losses during drilling operations.
The RSS has been widely used in directional drilling. In order to enhance wellpath control accuracy and efficiency of the static push-the-bit RSS, a powerful BUR prediction method is reconstructed by coupling a rotary steerable bottom-hole assembly (RSBHA) mechanical model and a drill bit–rock interaction model. This article showed that when establishing the RSBHA mechanical model by using the continuous beam column method, the steering rib should be treated as an eccentric stabilizer to consider the contact effect between the steering rib and wellbore wall. For the beam column containing the flexible sub and between two stabilizers, it should be rearranged into three beam columns, and the lower and upper steps of the flexible sub should be considered as virtual supports. The equilibrium tendency method (ETM) to predict the BUR can enhance wellpath prediction accuracy than those of traditional methods. Under 3D conditions, the total drilling tendency angle should be denoted by inclination tendency angle and azimuth tendency angle to enhance the solution efficiency. Case analyses have verified that the average forecast error of the BUR prediction model in this article is less than 1°/30 m.
Microcracks caused by perforating operations in a cement sheath body and interface have the potential to further expand or even cause crossflow during hydraulic fracturing. Currently, there are few quantitative studies on the propagation of initial cement-body microcracks. In this paper, a three-dimensional finite element model for the propagation of initial microcracks of the cement sheath body along the axial and circumferential directions during hydraulic fracturing was proposed based on the combination of coupling method of fluid–solid in porous media and the Cohesive Zone Method. The influence of reservoir geological conditions, the mechanical properties of a casing-cement sheath-formation system, and fracturing constructions in the propagation of initial axial microcracks of a cement sheath body was quantitatively analyzed. It can be concluded that the axial extension length of microcracks increased with the increase of elastic modulus of the cement sheath and formation, the flow rate of fracturing fluid, and casing internal pressure, and decreased with the increase of the cement sheath tensile strength and ground stress. The elastic modulus of the cement sheath had a greater influence on the expansion of axial cracks than the formation elastic modulus and casing internal pressure. The effect of fracturing fluid viscosity on the crack expansion was negligible. In order to effectively slow the expansion of the cement sheath body crack, the elastic modulus of the cement sheath can be appropriately reduced to enhance its toughness under the premise of ensuring sufficient strength of the cement sheath.
Hydraulic jet fracturing technology is one of the main means to develop low permeability and deep reservoirs. However, due to the large displacement and high sand ratio in the construction process, the erosion wear of high-speed sand particles on the hydraulic jet fracturing nozzle is more serious, which reduces the erosion cutting ability of the nozzle. Therefore, based on Finnie principle, a three-dimensional model of nozzle is established to analyze the influence of internal multiphase flow field distribution, flow rate, sand diameter and etc. on nozzle erosion. The results show that the erosion velocity increases nonlinearly with the increase of inlet pressure. With the increase of erosion time, the erosion rate gradually tends to be stable; with the increase of fluid viscosity, the erosion rate decreases; with the increase of the diameter and mass flow rate of the erosion particles, the erosion speed also increases, indicating that the size and mass flow rate of the erosion particles are the main factors affecting the erosion effect of the nozzle. The research results have important guiding significance for the rational use of the tool and the extension of the service life of the tool.
1 January 2023 in Fluid Dynamics & Materials Processing
The well-known “lost circulation” problem refers to the uncontrolled flow of whole mud into a formation. In order to address the problem related to the paucity of available data, in the present study, a model is introduced for the lost-circulation risk sample profile of a drilled well. The model is built taking into account effective data (the Block L). Then, using a three-dimensional geological modeling software, relying on the variation function and sequential Gaussian simulation method, a three-dimensional block lost-circulation risk model is introduced able to provide relevant information for regional analyses.