The identification of rockfall source areas is a fundamental work for rockfall disaster prevention and mitigation. Based on the Culmann model, a pair of important indicators to estimate the state of slope stability is the relief and slope angles. Considering the limit of field survey and the increasing requirements for identification over a large area, a new approach using the relief–slope angle relationship to identify rockfall source areas controlled by rock mass strength at a regional scale is proposed in this paper. Using data from helicopter-based remote sensing imagery, a digital elevation model of 10 m resolution, and field work, historical rockfalls in the Wolong study area of Tibet where frequent rockfalls occur are identified. A clear inverse relationship between the relief and slope angles of historical rockfalls enables us to calculate the rock mass strength of the landscape scale by the Culmann model and the relief–slope angle relationship curve. Other parameters used in our proposed approach are calculated by ArcGIS and statistic tools. By applying our approach, the potential rockfall source areas in the study are identified and further zoned into three susceptibility classes that could be used as a reference for a regional rockfall susceptibility study. Using the space partition of historical rockfall inventory, our prediction result is validated. Most of the rockfall source areas (i.e., 71.92%) identified in the validation area are occupied by historical rockfalls, which proves the good prediction of our approach. The dominant uncertainty in this paper is derived from the process of calculating rock mass strength, defining the specific area for searching potential rockfall source areas, and the resolution of the digital elevation model.

The influences of rockfall on human engineering have been increasing in Tibet with the rapid development of the western region of China. This study proposed a multi-approach to carry out rockfall investigation and hazard assessment. As a case study, the rockfall hazard from Nang County to Jiacha County in Tibet was assessed. Firstly, we summarized the characteristics of spatial distributions of typical rockfall sources using Digital Elevation Model (DEM) and unmanned aerial vehicle (UAV) aerial images with resolution of 10 m. According to the thresholds of slope angle, slope aspect and elevation distribution of typical rockfall sources, we obtained all of the rockfall source areas in study area semi-automatically in ArcGIS platform. Secondly, we improved the efficiency and accuracy of detailed field investigation by using a three-dimensional (3D) point cloud model and rock mass structure extraction software. According to the analysis result, the dominant joint set was J1, whose orientation was basically consistent with the Yarlung Tsangpo Fault. The combination of J1, J2 and J4 cut the rock mass into blocks of wedge with J1 as potential sliding planes. It was indicated that the stability of the rock mass in study area was mainly controlled by the characters of joint sets. Finally, we applied the improved reclassification criteria of the Rockfall Hazard Vector (RHV) method in rockfall hazard assessment according to protection capabilities of the current protection facilities, making the result more valuable for geohazards prevention work. Based on this multi-approach, we obtained that 10.92% of the 306 provincial highway and 9.38% of the power line were threatened by potential rockfall hazards in study area. The hazard assessment results of study area were also of certain guiding value to the linear project planning and geohazards prevention work.

The rock fall trajectory and its mechanisms are the most difficult to predict, owing to the complexity of the slope and the Irregular shape of falling rocks. To acquire a better knowledge of the rock fall mechanism of platy rock and to investigate the influence of various impact parameters, a comprehensive physical model experimental study was undertaken based on 3D printing technology using a high-speed camera and specially developed block release system. Based on the experimental results, the effects of the slope angle on the stopping position, the instantaneous kinetic energy and collision position of platy rock block were analyzed. Meanwhile, the effects of movement forms of platy rock before and after collision on the normal coefficient of restitution and the tangent coefficient of restitution were discussed. It is observed that rock fall trajectory depends not only on slope material characteristics, slope angle but also on factors related to the platy block (weight, size and shape). The experimental results showed the value of restitution coefficient exceeding 1 has an important relation with the combination of various movement forms (including the flip motion) and the change of movement forms of platy rock before and after the collision. A new feasible experimental method for research and prevention of rock fall disaster was put forward. It would be important and helpful to the geo-hazard control work.

Potential rockfall source areas are widely distributed in the high mountain areas of the Tibetan Plateau, posing significant hazards to human lives, infrastructures, and lifeline facilities. In a combination of field investigation, high-precision aerial photogrammetry, and numerical simulation, we took the Maoyaba basin as an example to explore a rapid identification method for high-altitude rockfall sources. An automatic potential rockfall source identification (PRSI) procedure was introduced to simplify the process of rockfall source identification. The study revealed that rockfall sources are concentrated in areas with intense frost weathering. Our identification results were validated using rockfall inventory data detection from remote sensing images and field investigation. Of the rockfall source areas identified by the PRSI procedure, 80.85% overlapped with the remote sensing images result. The accuracy assessment using precision, recall, and F1 score was 0.91, 0.81, and 0.85, respectively, which validates the reliability and effectiveness of the PRSI procedure. Meanwhile, we compared the rockfall source distribution of five DEMs with different resolutions and four neighborhood areas. We discovered that, in addition to high-resolution DEMs (i.e., 1 m and 2 m), medium-resolution DEMs (i.e., 5 m, 12.5 m) also perform well in identifying rockfall sources. Finally, we conducted a hazard assessment based on Culmann’s two-dimensional slope stability model and rockfall hazard vector method. Appropriate protective measures should be taken at high-hazard sections to safeguard pedestrians, vehicles, and related infrastructure from rockfalls.

Rock avalanche disasters in alpine and gorge regions are frequent and large in scale and cause severe damage. The movement of a rock avalanche is complex and has not been fully studied. The deposits of a rock avalanche can provide valuable insights into its movement process, which is crucial in understanding the rock fragmentation mechanism and predicting disaster-affected areas. Taking the Wangjiapo rock avalanche in Yunnan Province of China as an example, the size, shape and distribution characteristics of the deposit were analyzed based on field surveys, unmanned aerial vehicle (UAV) photography and image recognition technology. Initially, 3062 deposited rock blocks were manually measured in the field. Subsequently, the Particles/Pores and Cracks Analysis System (PCAS) was employed to identify 11,357 rock blocks with an area greater than 0.1 m² from UAV orthophotos. By comparing the characteristics of the rock blocks obtained through image recognition and manual measurement, the statistical analysis of UAV aerial imagery combined with PACS proved feasible in studying the Wangjiapo rock avalanche. The results showed that the rock block movement was accompanied by fragmentation and sorting processes; furthermore, the roundness increased with the migration distance. Small blocks were more prevalent at the foot of the slope, while irregularly shaped, large blocks dominated in source areas. The movement of huge blocks was characterized by significant potential energy-driven features and inertia advantages, allowing them to travel farther than smaller blocks, and they tended to be concentrated in the central area of the deposit. Additionally, affected by the cementation degree of breccia and the topography, the blocks in the eastern and western deposit areas exhibited different fragmentation and deposition characteristics.