Components produced by additive manufacturing (AM) via direct metal laser sintering (DMLS) have typical as-fabricated surface defects. As a result, surface properties of AM products should be modified to increase their strength, anti-wear behaviour, and at the same time to ensure their high corrosion resistance. Surface modification via shot peening is considered suitable for additive manufacturing of medical devices made of 17-4PH stainless steel. The objective of this study was to determine the effect of shot peening pressures (0.3 MPa and 0.6 MPa) and three types of blasting media (CrNi steel shot, nutshell granules and ceramic beads) on the tribological characteristics and corrosion resistance of specimens of DMLS 17-4PH stainless steel. Results demonstrated that shot peening caused steel microstructure refinement and—except for the nutshell shot-peened specimens—induced both martensite (α) formation and retained austenite (γ) reduction. 17-4PH specimens peened with steel and ceramic shots showed the highest increase in surface hardening by approx. ~ 119% (from 247 to 542 HV), which significantly improved their wear resistance. The highest mechanical properties (hardness and wear resistance) and corrosion resistance were obtained for the surfaces modified using the following media: ceramic beads > CrNi steel shot > nutshell granules. Adhesive and fatigue wear were two predominant mechanisms of tribological deterioration. Results demonstrated that the application of shot peening using ceramic beads led to grain size refinement from 22.0 to 14.6 nm and surface roughness reduction, which in turn resulted in higher corrosion resistance of the material. DMLS 17-4PH specimens modified by shot peening using ceramic beads and a pressure of 0.6 MPa exhibited the optimum surface morphology, hardness and microstructure, and thus improved wear and corrosion performance.

Shot peening is a dynamically developing surface treatment used to improve the surface properties modified by tool, impact, microblasting, or shot action. This paper reviews the basic information regarding shot peening methods. The peening processes and effects of the shot peening and cavitation peening treatments on the surface layer properties of metallic components are analysed. Moreover, the effects of peening on the operational performance of metallic materials are summarized. Shot peening is generally applied to reduce the surface roughness, increase the hardness, and densify the surface layer microstructure, which leads to work hardening effects. In addition, the residual compressive stresses introduced into the material have a beneficial effect on the performance of the surface layer. Therefore, peening can be beneficial for metallic structures prone to fatigue, corrosion, and wear. Recently, cavitation peening has been increasingly developed. This review paper suggests that most research on cavitation peening omits the treatment of additively manufactured metallic materials. Furthermore, no published studies combine shot peening and cavitation peening in one hybrid process, which could synthesize the benefits of both peening processes. Moreover, there is a need to investigate the effects of peening, especially cavitation peening and hybrid peening, on the anti-wear and corrosion performance of additively manufactured metallic materials. Therefore, the literature gap leading to the scope of future work is also included.

The paper investigates the cavitation erosion (CE) and sliding wear (SW) resistance of cold-sprayed Al/Al₂O₃ and Cu/Al₂O₃ composites and studies them in relation to a set of metallic materials such as aluminium alloy (AlCu4Mg1), pure copper (Cu110), brass (CuZn40Pb2) and stainless steel (AISI 304). The coatings were deposited on stainless steel by low-pressure cold spray (LPCS) using Al (40 wt.%) and Cu (50 wt.%) blended with Al₂O₃ (60 and 50 wt.%, respectively) feedstocks. CE resistance was estimated by the stationary sample method according to the ASTM G32 standard. The SW test was conducted using a ball-on-disc tester with compliance to the ASTM G99 standard. Results obtained for the LPCS coatings show that the Cu/Al₂O₃ coating exhibits a denser structure but lower adhesion and microhardness than Al/Al₂O₃. The Al/Al₂O₃ and Cu/Al₂O₃ resistance to cavitation is lower than for bulk alloys; however, composites present higher sliding wear resistance to that of AlCu4Mg1, CuZn40Pb2 and stainless steel. The CE wear mechanisms of LPCS composites start at the structural discontinuities and non-uniformities. The cavitation erosion degradation mechanism of Al/Al₂O₃ relies on chunk material detachment while that of Cu/Al₂O₃ initiates by alumina removal and continues as layer-like Cu-metallic material removal. CE damage of metal alloys relies on the fatigue-induced removal of deformed material. The SW mechanism of bulk alloys has a dominant adhesive mode. The addition of Al₂O₃ successfully reduces the material loss of LPCS composites but increases the friction coefficient. Coatings’ wear mechanism has an adhesive-abrasive mode. In both CE and SW environment, the behaviour of the cold-sprayed Cu/Al₂O₃ composite is much more promising than that of the Al/Al₂O₃.