Within the framework of the Density Functional Theory, the elastic, dielectric, and piezoelectric coefficients of w-ScxAl1−xN material were investigated for scandium (Sc) concentrations x = 0 to 0.375. The electro-acoustic properties are used to investigate the frequency response of the SAW delay line, based on the tilt θ° of the normal c-axis of the w-ScxAl1−xN piezoelectric thin film. We found that the piezoelectric response is improved as the Sc concentration increases, which is consistent with existing works in the literature. A 2D-phononic crystal pillars was then grafted on top of the surface, and the dependence of the acoustic band gaps is investigated with the help of the finite element method as a function of the Sc concentration and the tilted angle of w-Sc0.375Al0.625N. It was found that the two first band gaps exhibit a shift toward low frequencies with increasing Sc concentration. Moreover, the second acoustic bandgap is more sensitive to the inclination angle than the first. Furthermore, the insertion loss (S21) of w-Sc0.375Al0.625N is improved by 22 dB at θ° = 60°. The c-axis tilted Sc0.375Al0.625N-SAW delay line coupled with 2D-phononic crystals is a promising structure for low-loss and high-frequency SAW devices.
This study investigated the structural, mechanical, piezoelectric, and electromechanical properties of AlScN thin films using density functional theory (DFT) under varying levels of applied pressure, ranging from 0 to 20 GPa. The primary focus of this research is to explore the feasibility of optimizing AlScN thin films for surface acoustic wave (SAW) applications through pressure-induced modifications. Our findings reveal two significant outcomes. First, we observe a notable increase in the elastic constant C33 as a function of pressure. This increase signifies a substantial enhancement in material stiffness, directly influencing wave propagation and velocity within the thin films. Second, a remarkable 68% improvement in the piezoelectric constant, d33, is identified for Al0.75Sc0.25N at an applied pressure of 20 GPa compared to Al0.75Sc0.25N at 0 GPa. This enhancement has a profound impact on the electromechanical coupling characteristics of the material. These results underscore the potential for tuning the piezoelectric response of AlScN thin films using applied pressure, offering a promising avenue for enhancing the performance of SAW-based AlScN devices.
This work proposes a novel approach for the measurement of electrical conductivity in aqueous solutions of transition metal chlorides, specifically CuCl 2 –water, FeCl 3 –water, and NiCl 2 –water using a phononic–fluidic sensor. Indeed, it establishes a direct correlation between conductivity and the frequency of a cavity mode in the phononic crystal as a function of concentration. The phononic structure consists of air holes periodically distributed in a stainless-steel matrix. Meanwhile, the designed phononic crystal structure possesses a wide phononic band gap of width of 145 kHz that could be of a distinct effect through the detection process. By introducing a transition metal chlorides as defect in the central hole of the phononic crystal, the emergence of a resonant mode is expected which in turn represents the mainstay towards the detection of metal chlorides. In this regard, our findings investigated a significant shift in the spectral position of the resonant frequency with the concentration’s changes of metal chlorides, providing a superb sensitivity with respect to the concentration of 1.88 × 10 −4 (kHz ppm −1 ) for FeCl 3 solution, 1.80 × 10 −4 (kHz ppm −1 ) for NiCl 2 and 0.83 × 10 −4 (kHz ppm −1 ) for CuCl 2 . In addition, the highest figure of merit and quality factor values are obtained for FeCl 3 , which are 767.28 × 10 −7 ppm −1 and 162.75, respectively. Moreover, the lowest detection limits of the proposed sensor are 0.024 ppm for FeCl 3 , 0.039 ppm for NiCl 2 , and 0.061 ppm for CuCl 2 . In parallel, we performed direct electrical conductivity measurements for the same concentrations. A clear and consistent correlation between the resonant frequency and the electrical conductivity was observed. Based on this correlation, a calibration curve was established, enabling the indirect estimation of electrical conductivity from resonant frequency data. The sensor sensitivity with respect to electrical conductivity was found to be 0.1889 kHz (mS −1 cm −1 ) for FeCl 3 , 0.2056 kHz (mS −1 cm −1 ) for NiCl 2 , and 0.1548 kHz (mS −1 cm −1 ) for CuCl 2 .