The growing number of operations in implementations of the non-local fractional differentiation operator is cumbersome for real applications with strict performance and memory storage requirements. This demands use of one of the available approximation methods. In this paper, the analysis of the classic integer- (IO) and fractional-order (FO) models of the brushless DC (BLDC) micromotor mounted on a steel rotating arms, and next, the discretization and efficient implementation of the models in a microcontroller (MCU) is performed. Two different methods for the FO model are examined, including the approximation of the fractional-order operator ( ) using the Oustaloup Recursive filter and the numerical evaluation of the fractional differintegral operator based on the Grünwald–Letnikov definition and Short Memory Principle. The models are verified against the results of several experiments conducted on an ARM Cortex-M7-based STM32F746ZG unit. Additionally, some software optimization techniques for the Cortex-M microcontroller family are discussed. The described steps are universal and can also be easily adapted to any other microcontroller. The values for integral absolute error (IAE) and integral square error (ISE) performance indices, calculated on the basis of simulations performed in MATLAB, are used to evaluate accuracy.
This paper proposes a simple mathematical model based on the variable fractional-order difference equation of a robot arm. The model of the described arm does not consider the impact of the movement of the mobile platform, it was assumed that all degrees of freedom would be taken away from it. The implementation of the task was divided into two stages. First, a mechanical model was developed. In order to estimate the torques of nodal propulsion motors, a description of the components of the Lagrange equation for the considered system, i.e., energy, power, and external interactions, and derivation of the equations of motion of the tested manipulator based on the Lagrange equation was made. An additional criterion was also considered in the selection of drives in the kinematic nodes of the links, which was to set the manipulator in a vertical position at a specific time. Processing the measured data of a robot arm, model parameters were selected, and the order function was chosen. The second stage was a simulation, whose results were compared with the collected data.
This paper presents integer and linear time-invariant fractional order (FO) models of a closed-loop electric individual-wheel drive implemented on an autonomous platform. Two discrete-time FO models are tested: non-commensurate and commensurate. A classical model described by the second-order linear difference equation is used as the reference. According to the sum of the squared error criterion (SSE), we compare a two-parameter integer order model with four-parameter non-commensurate and three-parameter commensurate FO descriptions. The computer simulation results are compared with the measured velocity of a real autonomous platform powered by a closed-loop electric individual-wheel drive.
Determination of the physico-chemical interactions between liquid and solid substances is a key technological factor in many industrial processes in metallurgy, electronics or the aviation industry, where technological processes are based on soldering/brazing technologies. Understanding of the bonding process, reactions between materials and their dynamics enables to make research on new materials and joining technologies, as well as to optimise and compare the existing ones. The paper focuses on a wetting force measurement method and its practical implementation in industrial applications. Soldering simulation is a process in which simulation tools are used to model and simulate soldering processes. With simulation, different soldering methods and parameters can be tested to identify the best approach and minimize the risk of errors and failures in the real process. Soldering simulation can be used to optimize the soldering process and increase productivity, as well as to train personnel.
1 June 2016 in Archives of Metallurgy and Materials
Abrasive blasting is one of the methods of surface working before hot-dip zinc-coating. It allows not only to remove products of corrosion from the surface, but it also affects the quality of the zinc coating applied later, thereby affecting wettability of surface being zinc-coated. The surface working can be done with different types of abrasive material. The paper presents an effect of the method of abrasive blasting on wetting the surface of steel sheets by liquid zinc. Steels sheets following blasting with Al2O3 of different granularity and shot peening were examined. The worst wetting was recorded for a sample following shot peening - the results are below those for the reference test conducted for a sample not previously subjected to any treatment. Samples following abrasive blasting have similar parameters, regardless of the size of grain used for the treatment.
Determination of the physico-chemical interactions between liquid and solid substances is a key technological factor in many industrial processes in metallurgy, electronics or the aviation industry, where technological processes are based on soldering/brazing technologies. Understanding of the bonding process, reactions between materials and their dynamics enables to make research on new materials and joining technologies, as well as to optimise and compare the existing ones. The paper focuses on a wetting force measurement method and its practical implementation in a laboratory stand – an integrated platform for automatic wetting force measurement at high temperatures. As an example of using the laboratory stand, an analysis of Ag addition to Cu-based brazes, including measurement of the wetting force and the wetting angle, is presented.