An oscillating piezoresistive microcantilever (MC) coated with an aluminum (Al)-doped zinc oxide (ZnO) nanorods was used to detect carbon monoxide (CO) in air at room temperature. Al-doped ZnO nanorods were grown on the MC surface using the hydrothermal method, and a response to CO gas was observed by measuring a resonant frequency shift of vibrated MC. CO gas response showed a significant increase in resonant frequency, where sensitivity in the order of picogram amounts was obtained. An increase in resonant frequency was also observed with increasing gas flow rate, which was simultaneously followed by a decrease in relative humidity, indicating that the molecular interface between ZnO and H2O plays a key role in CO absorption. The detection of other gases of carbon compounds such as CO2 and CH4 was also performed; the sensitivity of CO was found to be higher than those gases. The results demonstrate the reversibility and reproducibility of the proposed technique, opening up future developments of highly sensitive CO-gas detectors with a fast response and room temperature operation.
Resonance frequency shift of a zinc oxide- (ZnO-) functionalized microcantilever as a response to carbon monoxide (CO) gas has been investigated. Here, ZnO microrods were grown on the microcantilever surface by a hydrothermal method. The measurement of resonance frequency of the microcantilever vibrations due to the gas was carried out in two conditions, that is, gas flow with and without air pumping into an experiment chamber. The results show that the resonance frequency of the ZnO-functionalized microcantilever decreases because of CO in air pumping condition, while it increases when CO is introduced without air pumping. Such change in the resonance frequency is influenced by water vapor condition, and a possible model based on water-CO combination was proposed.
27 March 2019 in Japanese Journal of Applied Physics
A microcantilever (MC) coated by Al-doped ZnO nanorods (AZNRs) was used for carbon monoxide (CO) detection at ambient temperature. Very high sensitivity (on the order of femtograms) was obtained, which is caused by the intense adsorption of CO molecules on the AZNR surface. After the samples had been prepared and characterized, the effects of the presence of water vapor on the CO detection were investigated. Although no response was obtained for AZNRs without the presence of water vapor (i.e. under a vacuum), high sensitivity was observed in the presence of water vapor (finite humidity). Regarding the above phenomena, we propose a model that is a replacement process of the water vapor molecules by the CO molecules on the AZNR surface and discuss it in detail.
In this study, highly-aligned and molecularly oriented poly(vinylidene fluoride/trifluoroethylene) [P(VDF/TrFE)] nanofiber webs were fabricated and their piezoelectric response was investigated. Using systematic post-treatments under appropriate conditions, a significant enhancement of the piezoelectric response in the P(VDF/TrFE) nanofiber webs was observed for the first time. The high-quality nanofibers exhibited a large output voltage of 0.4 V. The short-circuit current of post-treated nanofibers was found to be 731.25 μA, which increased about 330 times and the surface electric charge density was found to be 0.64 nC cm-2, which was about 2.7 times higher than those of the as-spun nanofibers. The large enhancement of piezoelectric response of the nanofibers is attributed to the additional stretching, annealing and poling of the as-spun nanofibers under the appropriate post-treatment conditions. The results highlight the potential of the high-quality P(VDF/TrFE) nanofibers to be used as wearable piezoelectric energy harvesters and other flexible self-powered portable devices.
19 June 2020 in Japanese Journal of Applied Physics
A highly sensitive (at the picogram order) Al-doped-ZnO nanorods (AZNRs)-coated resonant microcantilever (MC) for carbon monoxide (CO) gas sensing, operable at ambient temperature and under humid condition was synthesized. The ZnO nanorods were grown on the MC surface by using the hydrothermal method and doped by aluminum (Al). The sensitivities of un-doped and AZNRs for various CO gas concentrations were investigated by measuring the changes in the resonant frequencies and the Q -factor analysis of the vibrating MCs. The mechanisms of the remarkable enhancement of the sensitivity of the AZNRs-coated-microcantilever to CO were thoroughly investigated and discussed on the basis of energy gap between the highest occupied molecular orbital-lowest occupied molecular orbital of AZNRs and CO, active surface area of AZNRs, and the interaction of water vapor on AZNRs surface with CO.
Detecting methane (CH 4 ) at room temperature through adsorption-based sensing poses a challenge due to its inert properties. In this study, we enhance both the sensitivity and selectivity of CH 4 detection by decorating ZnO nanorods with platinum (Pt), forming Pt-decorated ZnO nanorods (PZNRs), which are then coated on a microcantilever surface. The sensor’s response is monitored by measuring the resonance frequency shift, ranging from 3 to 20 Hz, and Q-factor of 194 to 208, as CH 4 flows at rates of 10 to 100 ml/min under room temperature conditions. The introduction of Pt significantly enhances the sensor’s sensitivity to picogram levels, enabling the detection of extremely low concentrations of CH 4 . To assess the sensor’s selectivity, we compared its response to CH 4 with that of carbon monoxide (CO). The results demonstrate that the sensor exhibits a substantially higher response to CH 4 , with CO detection showing minimal (9 to 19 times smaller than CH 4 ) or no response. The presence of Pt atoms improves the ability of the PZNR surface to interact with CH 4 , which is further substantiated by Density Functional Theory analyses. These analyses reveal that the PZNRs exhibit greater selectivity toward CH 4 than CO, as indicated by the more negative adsorption energy for CH 4 , suggesting a more stable and favorable adsorption configuration. The combination of high sensitivity, exceptional selectivity, and room temperature operation makes this sensor a highly effective and advantageous solution for CH 4 detection, with potential applications in environmental monitoring, industrial safety, and energy sectors.