To ensure trajectory tracking accuracy and driving safety, this paper presents a real time nonlinear model predictive control (NMPC) method for autonomous guided vehicles (AGVs) to avoid dangerous load transfer effect in carrying heavy equipment. The AGV with a four-wheel-steering four-wheel-driving (4WS4WD) structure is controlled with a steer and velocity input for each wheel. The tracking problem is implemented by the standard NMPC framework and the referenced trajectory is planned by the Reeds-Shepp algorithm. A Large load creates a considerable load transfer effect which is dangerous for the wheels; hence, the controller limits the lateral acceleration to reduce load transfer. To realize online numerical computation for NMPC, the continuation/generalized minimal residual (C/GMRES) method is applied. A semismooth transformation based on the Chen-Harker-Kanzow-Smale (CHKS) function is introduced to handle inequality constraints since C/GMRES only solves standard equality forms. Trajectory tracking simulations are carried out in contrast to the quadratic programming method without lateral load transfer optimization, and practical experiments on an AGV carrying 13 tons of steel are also performed. The results indicate the accuracy, efficiency, safety and applicability of the proposed method on heavy-duty AGVs.
To paint large workpieces automatically, painting manipulators with hollow wrists must be transported by mobile platforms to different positions because of their limited workspaces. This paper aims to provide a visualization method for finding appropriate base positions (BPs) and maximum painting areas for manipulators. This paper begins by analyzing the motion characteristics of manipulators possessing a spherical wrist and summarizing them into three constraints – positioning, orientation and singularity avoidance. The hollow wrist is simplified and considered as spherical by introducing the concepts of an inner wrist center and an outer wrist center. Taking the three constraints into consideration, the boundaries of the manipulating space are formulated analytically. Finally, to verify the method, the space obtained is applied to determine the maximum painting areas for flat, cylindrical and conical surfaces. Experiments of robotic painting were used to confirm the results. Compared with previous studies, the maximum areas obtained using the proposed method increased by 17-131 per cent with an algorithm of lower complexity, and the process remained visually intuitive, thereby demonstrating that the method of manipulating space is more effective. Such a method allows individuals to visualize the entire painting area at the current BP, thereby maximizing painting areas or optimizing BPs. It opens a black box that is the relationship between BPs and blocks. The method can also be used to choose the best configuration for painting manipulators, select the end-effector structure parameters, split surfaces into blocks, etc.
1 March 2022 in NAVIGATION: Journal of the Institute of Navigation
Ensuring a convenient yet accurate localization solution is an essential problem in wireless-denied industrial scenarios. Therefore, in this study, a vision localization system with light emitting diode (LED) array targets for autonomous guided vehicle (AGV) navigation is proposed. The visible targets are calibrated and the pose can be computed using a camera that views the LED target. A novel data filtering method that integrates the odometer data and inertial measurement unit (IMU) data with vision data is introduced to provide stable and accurate localization. The vision localization system was tested on a 5-m-long AGV and the results demonstrated that the proposed system obtained a static position accuracy at 6 mm, kinematic position accuracy at 10 mm, and angle accuracy at 0.052°, which is more precise than the other methods used in industrial AGV applications.
24 June 2024 in IEEE Transactions on Instrumentation and Measurement
Sinusoidal fringe projection profilometry (FPP) is a promising 3D measurement technique. However, the accuracy of sinusoidal FPP will be seriously reduced due to the impact of the defocusing effect. Different from existing methods with constant fringe shapes, this paper proposes a defocus-driven variable-shape method that adapts the fringe shape to the defocusing degree to improve accuracy. The defocusing effect reduces the modulation of each harmonic in the fringe, especially the high-order harmonics. Taking advantage of this property, high-order harmonics can be introduced to the fringe to improve the fundamental harmonic modulation, thereby achieving a higher signal-to-noise ratio (SNR) without causing significant harmonic errors. With the increase of defocusing degree, more high-order harmonics can be introduced to the fringe, leading to a varying optimal fringe shape. This paper employs a parameterized fringe shape and an error optimization method to determine the optimal fringe shape for each defocusing degree. Then, the variable-shape fringe is generated according to the defocusing distribution of the measurement target. The experimental results demonstrate that the variable-shape fringe can achieve higher accuracy than the traditional methods with constant fringe shapes.
22 May 2023 in IEEE Transactions on Instrumentation and Measurement
Sinusoidal patterns are widely employed in fringe projection profilometry for high-accuracy measurements. However, in practice, random factors such as camera noise will seriously affect the accuracy of sinusoidal patterns. This paper presents a smoothed-truncated-sine (STS) pattern design method that can achieve higher accuracy than sinusoidal patterns under the same noise. By insensitive harmonic modulation, the STS pattern can achieve a higher signal-to-noise ratio (SNR) to reduce the random error and maintain the amplitude of sensitive harmonics low to restrain the systematic error. First, the error mechanism is analyzed, and the error model is established for the phase shifting algorithm, taking into account the resistance of the phase shifting algorithm to part of high-order harmonic errors. Second, a STS pattern is proposed and optimized based on the error model. The parameters of the STS pattern are optimized to achieve a high SNR and a small phase error, resulting in improved performance of the multiple-step phase shifting algorithm, especially when the number of steps is large. Simulations and experiments demonstrate that the proposed method achieves higher accuracy than sinusoidal patterns and that the maximum error reduction ratio exceeds 20% if the number of steps is sufficiently large in sinusoidal fringe projection profilometry.